Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
There are discussions on WLCSP light sensitivity for nRF5 product, which affects RF, clock accuracy, and low power current draw etc. what about the nPM1100 which clock accuracy...
Is my understanding correct that with VDD supplied and ENABLE = high, having VDD_GPIO floating (i.e. disconnected from a regulated 3.3 V supply) is a valid state? We intend...
hello Nordic
i am working with nrf52840 sdk16.0 s140
i wish to read the UICR register value like this :
but i get this compilation error
since it is a define...
Hello, I'm working the nrfx saadc legacy driver, and despite changing whether I measure Vdd(on the dk) or GND, the saadc output(p_event->data.done.p_buffer[0]) oscillates...
SDK14.0+NRF52832（PCA10040 demo board）:
I want to add static passkey to avoid MITM attack， I write code as following, but when I use the mobile app ‘nRF Connect’ to connect...
Dear community,
I need to operate a BM833A as I2C slave and to do so, I performed the following steps:
I modfied my sdk_config.h and set TWIS_ENABLED and NRFX_TWIS_ENABLED...
Hi,
I used nRF Connect for power profiler and programmer for hundreds of times.
But since today, it just keeps on showing white screen.
I tried "Ctrl + R" as well as...
Hi Team,
We are using the NRF52840 SOC for our development purpose and in our application we are planning to port the RTOS.
Could you please suggest us which RTOS is...
HI,
I am using the central_hids project in NCS V1.5.1 on NRF52840 , and now i want to add USB hid into the project, how can i do it?
I have try to do it in nrf_desktop...
Hello,
I've been trying to learn to develop an app based on ZigBee, it's the first time i'm working with nRF hardware and the only things i've done so far was to run some...
Hi,
I am currently trying to embed the ATT_MTU throughput example on two nRF52840 dongles. The main issue I am facing is that after I compile and program the hex files onto...
Hi everyone,
I am working with the nrf52832 Dk boards,
So my question is I want to connect sensors to two nrf52832 boards and want to get their data on a single Android...
Hi.
We use nRF5_SDK_17.0.2_d674dde as central
And phone as peripheral.
Usually system works correctly for a long time.
But sometimes it enter in strange state.
Connections...
Hi
I would like to store data in memory and to be able to read them after. But I don't know how to proceed ! I use IDE segger. Is it possible to store data always in a...
