Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Howdy ya'll,
I updated nRF Programmer yesterday (1.4.8 -> 1.4.9) and noticed binaries were not flashing to my board anymore. My JLINK is able to read the device's memory...
Hi, I am in need of some guidance. The overall goal is to set up MQTT/TLS communication from end devices in a thread network, via a border router to the AWS cloud. I have...
Hi. I am currently having a nrf52840 custom board and tried to program the sniffer hex file. nRF programmer gave me couldNotOpenDevice (0x4) Lowlevel error: JLINKARM_DLL_ERROR...
Hi all, I have a problem. I'm using a mix of the nrf samples azure_fota and azure_iot_hub connecting to Azure, using certificates X.509. The problem is the expiration date...
Hello everyone.
I have a nRF52840 DK that I am working with.
1.) When I plug into the USB port J2 (MCU interface) I am able to connect to the board program/debug using...
I wrote some code that has multiple custom services where my device acts as GATT Server.
I register the handler for every service (3 in total) with NRF_SDH_BLE_OBSERVER...
Hi,
I am debgging QSPI( type name: IS25LQ040B) in nRF52833, I met " NRFX_ERROR_TIMEOUT ", Could you give me some advice, please?
// Set QSPI pins to pins related to...
Using this \nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_blinky and nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_blinky_c
As described in \examples\ble_central...
Dear community,
I'm facing a problem during bluetooth scanning. I'm using the example named in the subject. This allows me to use the UART as debug printout.
I slightly...
Hi, I'm trying to upgrade nRF Connect SDK from 1.3.0-rc1 to 1.3.0 because I need one of the bugfixes to keep developing. I'm on macOS catalina and I've used the Toolchain...
Hi,
I am looking at and testing the ble_app_hrs_c_pca10040_s132 example.
When the whitelist ist set up with the "whitelist request" we execute the following two lines...
Hi,
I am developing an application that requires communication between two nrf52840-based devices. There is a scenario in my application where the devices needs to exchange...
Hi,
[179] RTC: COMPARE event is generated twice from a single RTC compare match
This anomaly applies to IC Rev. Revision 2, build codes CKAA-Dx0, QIAA-Dx0.
It was...
Hi everyone, I'm an intermediate level nRF Connect SDK IDE programmer, and I describe my issue below:
1.- In the link below I found an example of code for the analog port...
