Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi
I've problem on my design when I use voltage translator to communicate with sensors. Can you guys see pictures below:
1.nRF52840 using 3.3v:
1.nRF52840 using...
Hi all.
I want to send my packets in the negotiated time interval.
I sat the NRF_SDH_BLE_GAP_EVENT_LENGTH to 6.
The negotiated TI is 36 ms.
the results are
1- the...
Hello to all,
(If "TLDR" go to "### TLDR ###" in the bottom of the page, where you'll find the straight questions without all the context... ) Me and my team are using the...
Hi,
I noticed that the value raw_uuid_len in function ble_advdata_uuid_find() in module ble_advdata.c is fixed at the value UUID128_SIZE.
So the function can only find...
Hi, I am new to NRF and segger embedded studio.
So I want to send temperature sensor data connected with nrf52840 DK to the Murata1_SC device using UART.
The data will...
Found a potential "weirdness" with the mergehex utilty. When merging hex files containing code, dont seem to have an issue. Recently I was using mergehex create a full programming...
Hello Team,
Can you please confirm if we can use the crypto API to do AES encryption/decryption. Can I use it in non secure app and in application and not in bootloader...
Hi,
We want to make some BLE application for nRF52840 on Thingy:91. Referring to PCA20035 schematic, there are some spare pins which we assume is available for GPIO as...
Hi, we have a product (NRF51 SD8 S110 RBCMesh) on the market that craches about once per year the line that asserts is line 189 in src\\soc_radio_timeslot.c (your code) and...
Thanks in advanced. Platform is: nrf52832-qfaa, SDK_17.0.2, use V6.88a JFflash. I design custom board with cp2102n and nrf52832 to act as a usb receiver. All these boards...
Hi, I have flashed the nRF52840 dongle on macos (11.4) and ubuntu (20.04.20) using nRF Connect for Desktop (3.61) following the guide ( https://infocenter.nordicsemi.com/index...
Hi, I'm trying to run my app on a custom board, I keep getting the error "stopped by vector catch" before any of my code runs. I've tried sample programs for the equivalent...
Hello,
I am using one nrf52840 based SOC with nRF5_SDK_17.0.2_d674dde SDK for one of our project. I am trying to utilize internal 1MB of flash for storing some data. For...
Hello everyone,
I am working on a project using FDS. I am using the nRF52832 with the s132 SoftDevice.
As far as I can tell, the code I've written to store data records...
