Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
I am developing a Bluetooth Low Energy (BLE) application based on Channel Sounding (CS) using the nRF Connect SDK v3.0.2 on ME54BS01 modules from Minew Semiconductor (powered...
Hello DevZone,
Our team has been working on a customized firmware solution that has been flashed onto the nRF52840 DK to meet specific requirements.
We’ve noted that the...
Hi everyone,
I wanted to share an update on the BLE issue I’m experiencing with the BC40C (nRF5340) module on my custom PCB. I initially described the problem in this ,...
Hi,
I'm looking to use the nrf connect sdk for development that is compatible with the latest zephyr lts. I believe it will be ncs 2.9.2 compatible with zephyr 3.7.99 (3...
I set the parameters read from the Flash memory into sfdp-dfp in the Device Tree, but the Read command does not work correctly. Although I set the wait cycle for read operations...
I have used the Softdevice S130 2.0.1 and nRF5_SDK_12.3.0 the ble configuration code is based on the example of ble hids in the SDK The custom nrf51822 board only consists...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
New issue found, unsure if I can resolve this one! I have found the RTC1 may on rare occasion lock up, no love of resets, playing with LFSRC or RTC registers will make it...
Dir Sir
I have bought thingy 91 X for evaluation purposes
After activation of the Sim and, I have a constant green Led on
The device does not connect to the web application...
SDK v3.0.2 Toolchain 3.01
Is it possible to set the DIS name, (and possibly others) dynamically at runtime? I need to provide some level of configuration to my end users...
Try run Thread Certification with nRF52840 dongle, steps as below:
1. when Test harness is R62, Nordic devices work normally.
2. upgrade Test Harness to R63, and flash...
Hi,
We have 2 queries regarding I2C modes,
1. I2C fast speed mode
We are undergoing test of I2C under I2C_SPEED_FAST - 400Khz
when we enable this frequency on our...
Does ncs 2.5.0 implement the suggested workaround for https://docs.nordicsemi.com/bundle/errata_nRF52840_Rev3/page/ERR/nRF52840/Rev3/latest/anomaly_840_219.html ?
If not...
Hi
We met the problem is that clock low time period is out of spec, we got the value from oscilloscope is 1.24us@pull up resistor 10K/7.15k when clock speed=400kHz. The...
Hi
About nRF52840 I2C data read (CLK rate 400KHz)
1. Could you help check below three I2C items(tHD;DAT, tHD;STA, tSU;STO) can follow I2C standard(NXP) spec. or need follow...
