Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi everyone,
I am working on the USB_MSC example and I need your advice. I read an IMU unit and I want to store the data into a file. I create a single file to store the...
I am using nRF52832 evolution board and SDK version 15.3.0 in Segger studio(Ubuntu system) for Interface LSM6DSL accelerometer using I2C.
I am use TWI peripheral example...
Hi,
I want to program a nrf52832 module and a J-link debugger is on it's way. Until then I wanted to use my Black Magic Probe to flash and debug the application. I can successfully...
Hi,
We want to choose which frequencies we should implement on nRF9160 to have the best frequency bands coverage. Would you have a list of all known frequency band used...
I want to use the sensor example to transmit 10bytes of data at at rate of 10Hz.
I have tested the publishing using periodic publishing configured with the nRF Mesh app...
Hi,
There are many undefined reference error with file nrf_atfifo.h, already checked Makefile.am is included, please help to advice if there any file is missed.
........
Hello,
I'm using the following code to communicate my NRF52-DK with pc.
But sometimes the DK transmitting repeat data and sometimes error data is sent(missing 1 byte)...
Hello,
I'm implementing libuarte with ble_app_multilink. But receiver side receive gibberish like below.
It looks like RTT message is printed to serial port. But I...
I am using nrf9160 for a monitoring project using NB-IoT network. The problem I am having is when I go to an area where there is no NB-IoT network, the device crashes often...
Hi,
We've a custom board which has NRF52832 and Maxime. They are connected over UART. ( I'm using ble_app_uart)
What I want is transfer binary data between Phone and...
Hi, i am trying to understand the SDK 17 by building my own libraries such as interrupts, ADC, IIC or so on. I was doing well untill i come across with "LOG". When i look...
Newly purchased nRF51 DK connected via USB cable to a computer. Attempted to program firmware via BLE sniffer and an error occurred (image attached). Connected nRF51 DK does...
I am porting our firmware from SDK v15.3.0 to 16.0.0. I believe I have most of the changes in place as I am able to build the boot loader and get it to execute without any...
Hi
I'm trying to use Crypto but can't get started because micro-ecc isn't installed
The install instructions say:
Enter the subdirectory for the SoC and the toolchain...
I have been trying to bring up a secure boot loader for our product based on the nRF52832 SoC.
I have reviewed three SDK versions (17.0.2, 16.0.0, 15.3.0) and observe the...
