Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
I am using a customized PCB (nrf52840) and I have been successfully set up the SPI communication in between the nrf and lsm6dso
I used 0.11 as clk , 0.27 as MISO and 0.25...
Hello. We are testing nrf5340 - nrf7002 using the example of blpovisioning. I try to put on/off function using button, but if I reset pcb and turn on, it will connect to wifi...
I have our app on the nRF7002-DK board running with MCUboot configured for USB firmware updates. That is working fine, but is there some way to enable the console output from...
I'm facing issues with my brand new PPK2 tool What I've done so far, my setup : * Ubuntu, linux * I installed latest nrf connect application from official * Installed Power...
Hello,
I've been using nRF54L15-DK devboard (0.9.2 revision on the label) for about a month now without any problems until today.
I wanted to change VDD output voltage...
We are developing a system were we rely heavily on the use of LWM2M. Using the provided LWM2M client we normally dont experience any problems at all and are able to establish...
We're experiencing issues with RTT logging on an nRF9151-based project using NCS 2.9.0. When `CONFIG_LOG_DEFAULT_LEVEL` is set to `3`, RTT Viewer fails to connect to the device...
We have the Watchdog on the 5340 running but when we enter the software updater we wish to dissable it.
We have the following code to disable it but we are seeing the watchdog...
I have a private version of the VL53L1X driver ecause the driver in ncs2.9.0 hasnt been properly updated per my previous case. They suggested changing the CONFIG_VL53L1X=y...
Hi,
I am trying to get IQ data from nrf_dm_iq_tones_t and hopping sequence from nrf_dm_get_hopping_sequence with some clues from
I can see data but when I sort the data...
Hi,I have been using I2S communication in nrf54l15 DK board with zephyr but couldn't able to get clock to I2s .I couldn't able to get configure clock in overlay file ,can...
I'm trying to sign the application for nrf9160, starting with different instructions I found, but none of them leads to success.
I followed the intructions:
Generate a...
Hi
I have a nRF52832 Device, and develop by nRF5 SDK 17.1
Now, I have a project base on BLE_Central \ ble_app_uart_c , and also need to use Dfu OTA function
so I refer...
Hello,
I have an application that I have been working on that was based off of the peripheral_uart example that I am using with the nRF52832. I was trying to see if I can...
