We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Good afternoon,
The product we are developing contains some radios among which an nRF54L15 chip. At the certification company this chip is undergoing different tests. One...
I am programming firmware for the NRF52840-DONGLE. I have been able to get all the features I'm developing working, except I am now just trying to store a simple 10 digit...
I am using a custom board with a nrf5340 and vs code with sdk/toolchain version 3.0.2 and trying to get mcuboot working for FOTA. I have been stepping through mcuboot with...
Hi,I am now working with nrf5340 audio sample on nrf5340 audio DK .Here I can able to stream spho645 mic data to other dk board and able to listen using headphone .Now as...
hi Nordic.. i am trying to follow this link https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/exploring-the-benefits-of-mcuboots-compressed-image-support .. in...
Hello,
I’m trying to clarify the maximum ADC input voltage specification for the nRF54L15. Am I correct in assuming that it’s limited to the maximum IO voltage, i.e. VDD...
Hello,
I have developed a BLE Peripheral application on the nRF52840 (SDK 17.1.0) which works correctly. Later, I tried to integrate/port an SPI peripheral example into...
Hi,
I am a bit stuck with configuring nrf5340 project to include the bootloader properly.
The SDK-toolchain I use is v3.0.2
What I need:
encrypted and signed update...
Hello,
We are trying to increase the upload speed of our BMD-350 module. Right now we are averaging about 3kB/s according to nRFConnect.
See attached image of upload...
Hi No rdic support tea m, I'm developing a custo m appl ication on t he Thingy53 and have encountered challen ges implementing two key features that a ren't cov ered in the...
Hi all,
I'm trying to set up MCUMGR on 54L15, such that it can receive images from my border router when they're in the same Thread network. I read that we can upload images...
HI
A phenomenon occurs where the current remains at 20mA intermittently.
Actually, the BLE specification states that RF TX/RX is less than 10mA....
I'd like to know...
We are in the process of porting from nRF SDK v15.3.0 to v17.1.0.
After updating, we’ve noticed that the device sometimes gets stuck. Investigation shows this is related...
I have a custom board using a nrf5340 and a st7789 display using spi and mipi_dbi. It's I have it working on a sample project and printing "Hello World" I was using nrfConnect...
Does this mean that Bluetooth LE Power Control (LEPC) feature is not at all supported by any of the Nordic chipsets? I am particularly curious about nRF54 series with the...
