Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
Is it okay to supply the nRF21540 with a DC/DC or do I need to use an LDO? Are there any performance differences of the nRF21540 when choosing one over the other...
I'm finding that the signal strength of the radio is too low in my nRF52840 custom BLE project. I would like to increase the radio power from the default 0dB as our RSSI values...
I made a custom model under ncs1.6.0 to publish uart data. When the data I want to publish exceeds 85 bytes, an error occurs in debug:
<err> bt_conn: Unable to allocate...
NCS v1.6.0
CONFIG_SLM_GPIO_WAKEUP =y
CONFIG_SLM_INTERFACE_PIN =24
When Serial LTE modem is woken up after #XSLEEP=2 without 2s delay, it starts to loose some unsolicited...
Hello,
I'm using the sdk v17.0.2 with softdevice s140 with a custom PCB shipping the nrf52840.
I'm facing an issue where I cannot enable NFC and softdevice at the same...
Hello everybody. I am currently evaluating some BLE Tags, if they can be used as an BLE doorkey. The chips I am talking about are the following: nRF51802 nRF51822 nRF52832...
Hello support team,
I try to get the NRF52840 DK to work as a central with FreeRTOS. Connecting and getting notifications works well, but the device freezes on a disconnect...
I am running a Zephyr OS, and I am using the mbedtls APIs to do my cryptographic operations using the Cryptocell as my backend. My question is should I be using a mutex of...
Hello,
We have a physiological monitoring system in production where we used NRF52832 as a peripheral. Connecting this peripheral with Windows bluetooth, we realised that...
Hello,
I'm currently looking at using a last will message that updates an attribute on the cloud if the device disconnects from the broker. The broker and client agrees...
Hello everyone,
My current setup:
1.Development Kits = NRF52840
2.Nrfutil Version = 6.0.1
3.Softdevice = S140
4. Operating System = Linux
In current goal is to...
Hi There,
I am currently using a custom bootloader for my devices which was started from the secure bootloader example given in the SDK, I am using BLE as the transport...
i have nRF Connect SDK v1.6.1，excuted “west update” and “west zephyr-export” command（the project will not built successfully without executing these 2 commands）
then i was...
ncs version 1.6
SES
Windows 10
I have installed ncs completely using standard tools.
Now I am following the tutorial Part 1.
The project hello_world is created...
