We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
i have integrated the uart relevant parts from the app_ble_uart example to the pwm_driver example, i did the modifications to the sdk_config and defines
i get an error while...
I've been looking through the twi_master_using_app_twi example and been trying to change things around for use with a TMP116 instead of a LM75b. I noticed from the LM75b's...
I have been searching for the best way to authenticate / authorize a mobile phone with a nRF52 device without much luck.
I would like to ensure that only the owner of the...
In my situation, I want to use bluetooth to designed a piconet which has 1 master and up to 4 slave .
With yours suggestion,Now i make it work,in upload from slave to master...
I want to include a timer within a structure and also within an array. However the SDK uses a macro to define the declaration of a timer. App_timer.h recommends not to define...
Hi,
I am using nRF52840 and nRF52832.
1) I am seeing below statement in Product specification of nRF52840 under section “7.1 Pin assignments”. What does this mean...
Hi Nordic. I am using nrf mesh sdk v4.10 and an nrf52840.
I would like to report a potential bug regarding the Light LC server.
According to the mesh specification regarding...
Hello,
I have a strange Problem. I have a Central Application where the Central will get a TagID via Uart and if there is a adv. from this Tag the Central will connect to...
Hi Team,
We are using MBN52832 Murata module in our ongoing project.We need technical support from the team.
We need hardware integration (connection) support from the...
Every once in a while I am experiencing the soft device error NRF_FAULT_ID_SD_ASSERT.
In this post I saw that you may be able to provide some information on what is going...
Hello everyone,
I work with a custom board with the nRF52840 chip on it. We have pressure, humidity and temperature sensor and accelerometer sensor on the board. We need...
Hi,
We have a product that have a BLE capability (not by Nordic) and already have a mobile app that works with it.
I am developing now the FW for the upgraded version...
Hi devzone-team,
my application (custom board with nrf52840, sdk 16.0.098 ) uses 12 timers and it's organize in the 3 parts: uart, a pwm-bus ( proprietary) and ble-scan...
hi,
my application use boot and soft device.
Is possible with the application erase only the customer register in UICR ? (of course switch off the soft device)
This...
