Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
As a user I need to include stdbool.h before including lte_lc.h. lte_lc.h uses the bool type but does not include the appropriate header, so I get compilation issues if I...
use sdk:11.0
Reference routine：ble_nus_c
now I use 52832 to connect a device,the service UUID like the photo.
when I only discover one service UUID,like this code...
I am using an ADC where the SPI MISO pin also acts as a data ready pin when it transitions from Hi-to-Low as detailed in the link below. I am able to configure this and it...
Hi, I am new in Mesh using nRF52840, when I try to build the light_switch example, I link to all the libraries that project need and change the SDK_ROOT to the direction of...
The password I was assigned was 8 characters. I am so sick of these sites requiring logins and passwords that can never be remembered and frankly serving no purpose. I have...
=======
SDK: 15.3
Product all base: ble_app_template
Problem: cannot update iBeacon content dynamically during system run-time.
=======
we try to use ADV with...
SDK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
Hardware: nrf52DK PCA10040
nrfutil version 5.2.0
Hi,
I am trying to get the...
We have a custom nrf52832 board. We have nearly 260 boards. After uploading the app through DFU app (nRFConnect) , the new application starts to advertise . The application...
Hi,
We are using NRF52840 in our project.I am using SDK 15.3 and soft device s140 in keil 5 uvision. The NRF52840 Bluetooth will act as central and the other controller...
Hello. I am sending data from the multi-roll BLE module to the central BLE module using Notify. Currently, only the sample project HRValue is sent.
The data related to transmission...
Hello!
I'm using the nRF 52840 module for Zigbee applications. I am implementing a Zigbee router and I need the time-limited commissioning on the device, such as the creation...
Should it be possible to send SMS with the at_client example, and is there any special requirements to do so?
This is the AT commands setup procedure I've used:
AT+CFUN...
Can anybody help me please?
I'm trying to find a chip that will allow me to connect to my smartphone's internet connection over bluetooth.
I don't want to create an app...
I installed nRF connect for desktop in ubuntu 16.04. I added Programmer app . It was working fine till yesterday. But I update it from the nRF connect today. But now programmer...
Hello,
I try to use the opus codec on an 52840-DK. The Build and Flash with ARMGCC woks fine (with gcc-arm-none-eabi-8-2019-q3-update) but I'd like to use the debugger from...
