We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi
I am running UBUNTU 32bit
Which "nRF Connect for Desktop" version does run on 32bit LINUX?
I have tried several with no success.
Thanks for any help ti get...
hello.
I want test dfu example.
so I was compile & download secure_bootloader example(nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader).
I just compiled and...
Hello everyone,
I want to know about Connection parameters updated means and why to use it as mentioned above and when did the next connection parameter is updated and...
In a current project we have a nRF52 Bluetooth application where the Central communicates directly with a Peripheral (also nRF52). The nRF5 SKD V14.0.0 or newer is used for...
Hello,
I have been following this case to create my own bootloader for nRF52810, but I'm using gcc/Segger Embedded Studio instead of Keil.
I have modified bootloader_secure_ble...
Hi.all:
I'm doing a project, it include freeRTOS+emwin(TFT screen SPI-->32Mhz)+BLE(central+peripheral)+FATFS+flash(qspi)+TF card(spi)+GPS(uart)+wifi(uart)+other IC(spi)...
I am working with a SmartThings Multipurpose Sensor connected to a nRF52840-DK running the ZigBee CLI as a coordinator. I am able to have the sensor join the network and I...
SDK11, NRF51822
if I use the fstorage_test at the applicaiton_init(void), then runs ok.
but on my product, I use a key to power the system, if I use the fstorage_test...
We are implementing DFU over serial to the nRF52832 from another microcontroller.
We are using SDKv15.30 and a slightly modified the serial bootloader from the DFU bootloader...
Hello, I am developing a big project with the nrf52832 + several peripheral devices and I want to integrate the notion of unit test to my project (in Segger embedded studio...
When trying to build my BLE Mesh app based on light_switch server example app from nrf5 SDK for Mesh with added functionalities (like detecting GPIO state changes and firing...
I'm attempting to create a DFU update using the the ble_app_uart example coupled with the BLE DFU bootloader. It's not unlike this case .
SDK = v16.0.0
nrfutil = v6.0...
Hello Nordic Team,
I have loaded the ble_app_uart example on my custom hardware. There is a button connected to P0.13. When that button is pressed I receive a NRF_BREAKPOINT_COND...
Our nRF52840 is connected via UARTE @ UART_1 to a modem which does not have a WAKE pin - the only method of waking it from sleep is to send a UART break. Is there any way...
