I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hello,
we're just planning to deplay our first border router for bigger in-house installations and wan't to use a USB-Dongle with the nRF52840 as NCP with the Openthread...
Hi All,
We are working on zigbee protocol and wants to replace the existing setup with nRF52840 . We have some below queries need your answers on the same to go ahead on...
Hi
I'm developing an application that is pretended to run on an nrf52810-based custom board, The code is a modification of the blinky example from the SDK 15.0.0, and for...
Hello,
on my previous project i rellay enjoyed the offline documentation of the sdk (SDK14.2).
Since we are using the Thread-SDK now, I haven't found a offline documentation...
I'm using SDK 15.3.2 with SD 132. SES and the 10040 DK.
I'm not clear how NRF_LOG module and the new serial port library is support to work together.
I can easily make...
Hi Nordic!
In our design we see variations in the rev C lot we have received. We are using the VDDH REG0 regulator. Some of our ICs turn ON with no problem. And even when...
When I scan BLE device at nRF UARTv2.0 App in Android4.4, it is appar device name(Ex:Nordic_UART) and 6 byte device address(MAC address?).
I want to include mac address in...
The button is connected to ground directly ,and without external pull up resistor.
I found it consumes too much current when using internal pull up resistor,but when I use...
According to at client demo, LTE-M1 is the default mode in firmware mfw_nrf9160_0.7.0-29.
Modem work mode will be LTE-M1 after every reset even you changed to NB1.
I...
I am receiving an error when I try to update my custom characteristic in a custom service, which was all working fine until I started playing with app_timer to read battery...
Hi,
would like to run several (8) BLE_HRS_C in parallel to one BLE_NUS on a nRF5. Can that work?
In general, is it there any sample code showing how to implement peripheral...
Hi,
I'm doing a project of a bluetooth sensor, using pca10040 with softdevice v5.1.0 s132 that sends data to one or more android applications simultaneously, in this project...
I've got Wireshark running with nRF Sniffer, but it is not really working for me.
I'm using a PCA10040 board as the sniffer hardware.
I'm running on a Mac with MacOS 10...
I tried to set up the programming Environment for Windows 10 by following the "Getting Started Assistant" from the "nRF Connect SDK" program. When I finally came to the point...
