I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi there,
We're looking to improve the touch performance of our products by moving from PCB electrodes to a dedicated touch film. Can anyone provide any references to info...
Hello Nordic team,
What is the Maximum sampling frequency for i2s we can configure to nRf51 or nRF52 DK?
And if we enable UART module to print live of i2s on serial console...
Hi
I following the steps listed in the document Thingy Mesh Demo v0.1
https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
When i perform the step 5 "Open the...
Hello,
I am using sdk12.2.2 and nrf52 customized board. I want that user should be prompted to enter passkey before bonding. I refereed the code snippet from devzone and...
Hi!
Im using SDK14.2 and I m working with the custom characteristics tutorial(the one compatible with the SDK 14.2).I have an SDK5 device connected to a LORA radio with...
Hi,
I’m having some troubles writing into the fash memory. I work on KeilµVision.
I initialise flash doing :
uint32_t page_size = NRF_FICR->CODEPAGESIZE;
uint32_t...
I am adopting a project which was initiated by someone else. I am using GCC toolchain eclipse while previously used by other colleague who initiated the project used IAR....
Hi,
My product is automagically disconnected from the central after 9min of connection...
The same problem can be reproduced from the ble_app_template example as is, on...
Is it ok to execute the following program twice in succession when communicating data of 244 bytes or more with one communication?
do { err_code = ble_nus_data_send(&m_nus...
Hi Devzone,
I would like to print my payload on a hyperterminal using NRF_LOG_INFO().
My array is like that :
manufacturer_data [0] => Value: 0xAA; manufacturer_data...
Hi all!
I am approaching this with pretty much zero experience but what I'm trying to build should be a piece of cake for you so any help, example code, advice will be appreciated...
Hi Nordic,
I'm using nRF51, SDK 12 and softdevice version S130 to stream data from nrf51 to iphone6 over BLE.
Sometimes, Few hours after launching streaming, the BLE...
This is almost certainly a benign bug, but it doesn't hurt to point it out.
In nRF5_SDK_15.0.0_a53641a, nrf_drv_saadc_channel_init() is a macro that expands into a call...
We use nRF24AP2(USB) in our product but we need transmitter a CW(with modulation) output and RX BER test in FCC.
How can I do it? I would like to use SDK to control nRF24AP2...
