My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
I am using nRF52840/nRF52833 (raytac module, original board). With the current nRF Connect SDK, is it possible to disable NFC and use ports (P0.09, P0.10) as GPIO?
I am...
Hello,
we are currently in the process of verifying the nRF LwM2M Client, specifically focusing on the Queue Mode functionality. During our testing, we encountered an issue...
Hello,
I am facing issue while initialising seed by calling "mbedtls_ctr_drbg_seed" function I am getting -0x34 error and when I analysis this I got to know that I have...
Hello,
It has been a while since I have done any controlled impedance and was wondering if someone could provide me a quick sanity check before I continue:
Here is the...
Hi,
Does nRF52840 support stable modulation Characteristics
It is found that Stable Modulation Characteristics fail during the test, and the capacitor of the debugger...
Hello everyone,
I'm using nRF52832 with SDK v17 (S132 Softdevice).
I don't know why, but I can't disable softdevice. I can enable it normally, but when i make use of...
Hi,
I’m looking to monitor LTE-M or NB-IoT packets sent by the Thingy:91 in real-time using an app or software. Currently, I’m using the Thingy:91 to send temperature logs...
Dear devzone,
I followed this instruction to use nRF54L15-PDK v0.8.1 to burn external boards. The wiring diagram is as follows:
Command line input: nrfutil device recover...
I have a Minew MSR01-B milimeter wave sensor and I would like to know if there is any nordic hardware that i could use to comunicate with MSR01-B sensor, get the data and...
Hello,
I am designing a battery monitoring circuit for a 3.0V CR2032 coin cell using the nRF52840, and had some questions. I am following the battery monitoring circuit...
Good afternoon,
I have successfully established a 2.4GHz Zigbee network using nrf52540 + Zephyr + ZBOSS. Now I need to switch to sub-1GHz band - suits better my application...
Hello,
I am trying to implement BLE DFU with nRF7002DK and SDK 2.7.0(Sorry but not use sysbuild yet.)
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
Hi! I'm trying to find examples for a use case we might be exploring. Specifically, we'd like to connect an nrf52833/20/other to an Ipad over a USB HID interface. The connection...
I am trying to work through the Dev Academy - nRF Connect SDK Intermediate - Lesson 3 Exercise 1. I have run into a problem in step 8. Everything prior has gone OK and I successfully...
