Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
How to change Device Information in nRF Cloud? Where do I find the code setting this info? Where is "App Name" and "App Version" defined?
The application is nrf_cloud_multi_service...
I am tring to use this spi bitbang example to write epaper
https://docs.zephyrproject.org/latest/samples/drivers/spi_bitbang/README.html#spi-bitbang
Here is my code
...
Hi,
i want to view the debug logs using the printk function while using the debugger in nrf5340 dk kit. we use RTT viewer to view the debug logs printed using printk function...
I have been trying to:
add MCUBOOT and FOTA to a custom BLE board using the nRF54L15.
I had thought that the sole issue was that the custom board does not utilize...
Hello, I have a minor problem with starting up i2c0 and i2c1. I am trying to run a scanner in the sample code that will print out the addresses connected to these buses. I...
Hello,
I’m using the GNSS sample (located at C:\ncs\v2.9.0\nrf\samples\cellular\gnss ) to evaluate the GNSS module on our custom PCB, and I need to view its output over...
i am writing an absolutely minimal "bare-metal" application for the nRF54L05 -- one that doesn't use the zephyr kernel or drivers....
all i really need at this time are...
I am trying to use uart21 on nrf54L15-PDK. And I have try some port 1 pins already, and they works well. However, we need to use port2 pin 7 & pin 8 for uart21. But I get...
In my project I am facing issues to send 6000 bytes per second through BLE to androis app
For reading the sensor it is taking 30-40 ms processing time and after that I am...
Hello all, I'm getting stuck on re-installing any SDK and I'm getting the below error. The error:
Failed to clone the repositories: Error: HEAD is now at 100befc70c7 [nrf...
This would be a continuation from a previous discussion on the topic of Bonding information and the process of bonding between the peripheral aka headset and central device...
I am using nRF52 based NINA-112b EVK I saw the spi master example to send the data to slave. Do you have any idea what to do if I want to receive the data from the slave....
I am getting an error
warning: SPI_NOR (defined at soc/gaisler/gr716a/Kconfig.defconfig:18, drivers/flash/Kconfig.nor:6) was assigned the value 'y' but got the value ...
Hello,
For a month I have been trying to find a solution to update my devices which are at my customers (these devices have a bootloader, softdevice and app coming from...
Hi
ncs 2.6.1 / toolchain 2.7.0
we have developed a Product using ANNA-B402 (with nRF52833).
Now we made a product variant with nRF52833 WLCSP. Both use the same application...
