Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Dear devzone, nRF54L15 runs private 2.4g, and needs to switch from 2400MHz to 2500MHz. How long is this period? How long is it to switch from 2400MHz to 2410MHz? I see from...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
The chip I am using is 54l15, and the NCS version is 2.8.0
I used the peripheral_uart example for modification and got my own program, but I forgot which time this problem...
Hi Nordic
Asking this question to Nordic AI (right-down window), below was the answer.
The nRF9160 is a cellular IoT device, and its MTU size depends on the protocol...
I am programming a RAK4631 Board, which is of course based on the nrf52840 SoC. The BaseLine Device tree has no detail in the ADC Node so I have created an overlay. The RAK4631...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
The design has an eSIM and a regular SIM, with a switch driven by a GPIO line. We default to the regular SIM, but if the library...
Hello,
How can I check which crystal oscillator is configured for the nRF52832 DK from the firmware side? Is there a specific configuration file or parameter that defines...
Hello,
I have a Python script that analyses some sensor data. If a condition is met I want to send a trigger via ESB to a peripheral board (ESB chosen for its low latency...
Hello, I'm having issues when building the peripheral_nfc_pairing and central_nfc_pairing samples from ncs 2.2.0 in VSCode. I've build before and haven't gotten any errors...
Hi,
I’m currently working on a Zephyr project using the nRF Connect SDK, and I am looking for a way to setup the toolchain for my terminal emulator (specifically using zsh...
Hi
I'm new on zephyr and nRF9160.
In the nrfx source are lots of NRFX_ASSERT() macros.
This macro checks a condition and thrown a exception.
Normaly we use asserts...
Hello everyone,
We are using the NUS service to transmit some data. To comply with certain CEM tests and regulations, we need the ability to configure BLE to publish on...
Hi,
I'm working with the nRF21540 Development Bundle (DB) , which includes the nRF21540 DK and nRF21540 EK . I need to use the FEM module with the GPIO+SPI interface to...
