Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
First off, I see a new changed requirement for making Public tickets:
To raise a public support ticket you need to provide your location in profile. profile Please fill...
Hi Everyone,
I'm having problems getting GPIOTE_IRQHandler_v() to run.
"NRF_GPIOTE->INTENSET = 1" causes my Nano 33 BLE to crash if "(GPIOTE_CONFIG_POLARITY_LoToHi <<...
Hi!
I want to use the function strptime from time.h to convert a timestamp to unix time but get the error "implicit declaration of function 'strptime'; did you mean 'strftime...
Hi,
I am new to microwave board design, so I'd like a little advice please. I have attached photos of the 2.4ghz section of my board and would like to know if the component...
Hi,
I'm trying to integrate the secure_bootloader DFU code into the ble_app_uart_c example but am stuck on an error regarding not fitting in an 'UNPLACED_SECTIONS' region...
I'm trying to develop an Android app to get the BP, HRV, HR, SpO2, ECG, PPG, BPM, steps, activity, temperature, sleep quality from Spovan H02 fitness tracker ( www.spovan...
Hi, I am using Mesh v4.2.0 and nRF52840 light_lightness example but instead of button_event_handler, I am using GPIOTE to control the lights.
I want to toggle one LED with...
Hi
We are developing a system where 2 devices (NRF52840) advertise to each other (and eventually connect) in a highly reflective environment (the cargo hull of a ship)....
As mentioned here I installed the Intel versions:
VS Code 1.63.0
nRF-Command-Line-Tools 10.13.0
J-Link V7.58e
nRF Connect for VS Code
But flashing the sample...
Hi,
We are trying to work pc-ble-driver on Windows with CODED PHY.
it works with 1Mb PHY but not with CODED PHY.
I changed the MAX CONNECITON INTERVAL to 500, but...
We have a custom board with NRF9160 SIP and it has a provision to flash using SWD interface. SWD_IO and SWD_CLK pins.
My connection is like below
VDD and VTG is shorted...
I've tried activating my sim from multiple browsers and it either gets stuck at the first screen where it wants the SIM# and PUK or or on the second screen where it asks for...
Hello, Nordic employees.
I am currently developing BLE5 app with nRF52840 DK and Python in Windows 10 environments.
With the python bindings you provided in the github...
I've been taking an inventory of MDK updates that have come out since the one used for my project was last updated. I was browsing through the notes on this page , thinking...
1. There is no compile-time error while building the code
2. but while debugging -
The following runtime error we are facing -
<info> app: Sensor Init successfully ...
