Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I am new to IoT development, and am working with the Nordic Thingy:91, and nRF9160 development kit as a starting point for development. Is there a preferred operating system...
Hello,
im using nrf52840 with sd140 and sdk17.0.1
in my project i have implemented a libuarte communication that works well usually, but rarely, and usually after days...
Device Name : nRF52840-DK PCA10056
I have 4 questions listed below, the reason is Instead of creating multiple ticket/case we can follow up using the same ticket to avoid...
Hi! Thanks for reading this post. I'm having an issue creating a firmware package for our manufacturer. I'm using a nRF52832 with SDK version 15.3.0_59ac345. Whenever I merge...
I have a question about the baud rate of the UART. I have set the baud rate of the UART to 19200bps, but can it work without a problem even if there is a percentage difference...
Hello,
I have trouble to create a project on NRF9160 DK.
I follow all the steps on getting starting guide and i also check all the steps on getting starting assistant...
Hi Team,
Nrf52840 DK acting as central and we trying to connect our peripheral device, we observed below logs with total duration of around 300ms.
Is there any way limit...
Hi forum,
I am working on nrf52832 using sdk15.0.0. using project ble_app_beacon.
In this project I am setting tx_power 0dbm,4dbm,-4dbm and -8dbm.while setting this tx_power...
Hi, Nordic
nRF52 as GZP Device, nRF24 as GZP Host
I know if nRF52 is range of nRF24, the pair will be worked.
I want to know what is the distance.
And if I use unencrypt...
Hi everyone,
I work on an custom board with the nrf52840, the SDK 15.2.0, the SoftDevice 140 6.1.0 and FreeRTOS.
My problem is that during a BLE transfert of a lot of...
Can I develop a software with MESH network support (1MBPS) and 16 Central links (CODED_PHY)?
All my tries is unfortunaly. But I dont give up.
Just guide me please and...
Hi, I have 2 nRF52840 D K but suddenly both are not showing on my PC. I have checked my data cable which is working fine on mobile and transferring data. I have also checked...
Hello,
I am evaluating the possibility to use ESB protocol on nRF52840 development kit. As far as I understood, for HW limitations, the maximum number of pipes in a star...
Hi all.
I want to increase number of sending packets in TI. I searched for the answer and I found answer wasn't for v7.2.0.
please give me a solution for v7.2.0 sdk ....
Hi
I want to receive data through UART RX interrupt.
--> A n interruption occurs to notify me w hen one character(byte) is received, and i store it to my memory buffer...
