Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
got a question about UART and maximum bytes it can receive in one burst or "packet".
Using nRF52382 and SDK16.
Recently I've been developing a new app in which UART...
Hi Nordic Team/public users,
Request your assistance for troubleshooting the NDK-nrf52840 board that was having a detection issue whereby my laptop/PC was unable to detect...
Hello, I hope you are safe and well during these times. I have created a successful prototype using the Adafruit Feather nRF52 Bluefruit and the Arduino IDE. I think I am...
Hi,
I want to update the DFU with application nRF Connect (Bluetooth) for beginning I want to try with nRF Example in example/dfu/bootloader_secure. The file secure_dfu_secure_dfu_ble_s130_pca10028_debug...
Hi,
I like to use nRFSDK in my future project, but I don't like the hectic steps to open a project when using nRFConnect SDK. I cannot open Segger IDE directly instead go...
Hi everyone,
Currently, i am working with some zigbee devices using NRF52833 and zigbee SDK 4.1. Now, i want to use BLE DFU with it to update the firmware when needed. ...
I am developing with NCS, but I found only one project "v1.4.99-dev1\nrf\samples\bluetooth\peripheral_lbs" I can add files directly through the option "Add new file to cmakelist...
I m using sdk16.0.0 nrf52-ble-app-uart-c-multilink example. I want to comminication arduino btw BT840F. I try with nrf52840 there is no problem but when i use bt840f i didn...
I'm using a library that does
#ifndef MIN
#define MIN stuff
#endif
Because I'm using segger, I have no control over compilation order, so that's getting loaded first...
I want to design the chip (nRF9160) on our board. 1- What kind of external debug / flash (SWD) can I use to flash the modem firmware and my app?
2- Is there any suitable...
Hello All,
I am implementing a simple UART bridge over BLE and want to add a Characteristic to update the baud rate being used. I thought I added code to support a new characteristic...
Hello!
I have this interesting bug with the twim driver.
It works perfectly with the NRFX_TWIM_XFER_TXRX transfer type: I see the transaction go out on the bus lines...
Hi,
My project uses nRF52840 with SD 140, SDK 17.0.2 and SES. My hardware has SD Card SPI and LCD SPI sharing bus pins, using CS pins to switch devices. Because of this...
Hi,
When I use Texas Instruments CC2650 MODA (using Bluetooth 4.2) as the the transmitter, a smartphone (iPhone or an Android phone) that has nRF Connect app as a receiver...
