Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,
I am running into some problems with libuarte. I have two nRF52840-DKs talking to each other over UART. My setup is not ordinary however. The hardware configuration...
Hello -
We are developing a product for the nRF52840 using SDK v17.0.2 and FreeRTOS. Our application uses the RTC configured by FreeRTOS to implement a System ON sleep...
While installing the itsybitsy NRF52840 board from Adafruit in the Arduino IDE, I encountered the following error:
"Tool nrfjprog is not available for your operating system...
I can't get a button to work on a custom board; but same firmware HEX file on a different board works fine.
Using nRF5 SDK 17.0.2, SoftDevice S132 v7.2.0.
using a custom_board...
Hi,
I'm using an nRF52840 and I need to implement a driver in c for an external chip. The c driver is written, and I only need to add specific functions regarding the SPI...
I can't see the answer, so I will write it again.
hello.
nrf24l01p(ptx), nrf51822(prx)
nrf24l01p set
TX_ADDR = 0xA5B300
EN_AA = 0
EN_RXADDR = 1
SETUP_AW =...
Hi, I am trying to add Buttonless DFU functionality to the ble_app_blinky example.
The process I took
1. added the following files to the project
ble_dfu.c ble_dfu_bonded...
Hello, I am trying to implement a basic BLE connection between the nRF52840 Dongle and an Android Device (nRF Connect). I wanted to secure this BLE connection with a passphrase...
Hi everyone,
I am working on buttonless OTA DFU. I have generated my own private and public keys using nrfutil and created the .zip file for DFU.
While generating the...
Using the following image UUID on NRF51822, how do i connect to the host in the nRF5_SDK_12.1.0_0d23e2a softdevice? I used to the example of ..\ble_peripheral\ble_app_uart...
Hi,
I used one nRF52840 dongle and one DK, and placed one sniffer in between to caputure the packets.
The connection interval was set at 7.5 msec, GAP event length is...
I have gone through the nWP-034 document (nRF9160 Hardware Verification Guidelines) and wonder if it exist sample code (firmware) to be used, as a baseline, during regression...
Hi,
we have interfaced Accelerometer Module with NRF52832 using SPI Communication. Psuedo code of code snippet is :
<<Place the snippet here>> Expected : After nrf_spi_transfer...
Hi,
I am trying to use APP_TIMER to detect if a sensor isn't responding to I2C Commands. I created and started the timer with the following steps. The project is based...
