Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello all !
So here is my problem, I have a computer as a CoAP client running the Python script from : https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
i use a 52832 module scan BLE advertisement signal, and found it can recived lowest DB value is -92db. but i use my Phone to scan same advertisement signal, it can recived...
Hi
I am using the nrf52832 DK for my project.
Using ble i need to establish wireless connection b/w the android phone and the board.
I need to send data from the phone...
During manufacturing verification we want to run some tests that will require us to talk to our custom nRF52840 device over bluetooth.
The ideal solution for us would be...
Hi
In the infocenter, I can find the important note which says, that to run nRF5 SDK for Mesh v2.2.0 on an nRF52832, nRF5 SDK 15.0.0 as well as the softdevice S132 v5...
The scratchpad is overflowing when generating a keystream prior to a CCM decrypt operation.
The size of the scratchpad is calculated according to the formula in the product...
is there any tutorial that shows me how to read data from the BLE using android. My NRF 52840 is connect to my device(Which is i expected data to read from) i am able to send...
To the kind attention of Nordic,
while I'm planning to do a software porting from nRF24 to nRF52840, I've been studying some of the usb applications you provide in your...
Hi,
I am a newbie with zigbee on nRF52840.
I have tried serveral days with zigbee SDK but have troubles to work.
Finally i have found that example zigbee/light_control...
Hello!
We have nRF52832 chip on our product and we have some problem with one of its IOs.. We configured P0.16 as RX of UART, And when we run it we see this behavior of...
my example project: wireless_uart_raw_first_pca10056
chip : nrf52840.
i want to make my application timer in the my example project. time tick is 100 msec. in every 100...
Is it possible to get the Build Type from the Factory information configuration registers (FICR)?
From https://infocenter.nordicsemi.com/topic/comp_matrix_nrf52832/COMP...
Hi
I have some question about OTA .
1.The nRF SDK hvae twos way for OTA: single bank and dual bank;The nRF Mesh 3.10 too?Because my firmware maybe very large,so I want...
Dear all,
I am having issues with service discovery of two primary services ( Battery and one propriotary based on NUS) I am currently using SDK 14.2 on NRF52832 chip running...
Hi, I'm trying to use the Seggar Embedded Studio to debug my code, but the Seggar Embedded Studio can only recognize the nRF52840 development board, not the external device...
