I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi,
I have a working application with Buttonless Secure DFU Service wich runs on nRF52832. I'm able to perform DFU without bonds, but I want to use bonding in my application...
Direct connection after disconnect I am using the iPhone 8, BLE device (51822/51422), s130, SDK 12.3.0.
and using a bonding and passkey to connect.
However, Direct connection...
Hi there
I met an error down below.
nrf_log_str_formatter.c(86): error: #29: expected an expression
if (RF_LOG_STR_FORMATTER_TIMESTAMP_FORMAT_ENABLED)
nrf_log_str_formatter...
Does the serial function operate with a soft device. Whenever i have an include statement for serial.h in a file with a softdevice I get a No such file or directory compilation...
I've been going off of the Buttonless DFU example to integrate DFU functionality into an existing project on a custom board. While I seem to have added the necessary includes...
I am programming a BL652 module (contains an nRF52832 with populated DC/DC inductors). I am programming it through the nRF52 DK in SEGGER studio.
When I run the blank (no...
Hi All,
A very general question here. I understand that using pre-defined services like the battery service help standardize the way peripherals send data to the central...
I'm using JLinkRTTViewer to look at RTT output from my code. The problem is that when I try to go into POWER_OFF, it generates a reset instead.
Is there a way to go into...
hi,
We want to position with aoa(angle of arrival) method, can it provide the One IQ-sample is a pair of in-phase and quadrature-phase samples, and Phase and amplitude information...
Hi,
I am using a nrf52840 development kit flashed with the ICMP example provided in SDK 15 and I am using a device with Bluez tools version 5.47 to connect to it.
However...
While investigating problems I'm experiencing with bootloader_secure I believe I've identified an error in the HCI TX finite state machine ( components/serialization/common...
We have implement a PPI for device match to trigger a GPIO toggle . but now we want to trigger a SW interrupt or a callback function .
my question is how to set PPI TASK...
Hi,
I merged UART exam ple from nrf5 sdk v14.2 with light switch client example from mesh sdk v1.0.1, i have 2 boards client board which is nrf52832 and server board which...
I'm developing an application using the NRF52832. Im using the ADC, and there may be times where the NRF52832 has 0V on its supply pin, but the voltage on the ADC pin is nonzero...
Dear Nordic Support,
does the BLE Uart example (SKD 14.2) inlcude any data link layer machnisms, for example error detection & correction, collision avoidance?
I implemented...
