Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
This is the normal kconfig menu.
But it often happens that the following picture does not recognize anything in kconfig
and there is no devicetree option in the action...
Hello Nordic,
We developed our product using MCU NRF52840-QFAA-F-R. Our client is based in the EU. We plan to launch our product in 1-2 months.
I have a few questions...
Hello,
I am working on a prototype Bluetooth Low Energy module using the MDBT50Q-512K (by Raytac).
To measure the frequency of this prototype with test equipment, I am...
has been helping me connect to a device and I am finally able to do that, but as soon as I do, Zephyr crashes.
This is with a lightly modified central_uart project [00:00...
While creating a new board in step 2 of the exercise, there are a couple of problems with the sub-steps 1-5:
First, sub-step 1 says to name the board "DevAcademy nRF52833...
Hello,
I've been using the libuarte module in my project, and I done a power consumption reading. With libuarte switched on I'm consuming 0.78ma, and with it switched off...
We have been seeing a bootloop issue on some of our nRF52840 boards running NCS v2.6.1 using CR2032 coin cell batteries. The batteries are all around 3V.
This is an intermittent...
ON NCS SDK 2.7.0 version, how to calibrate SAADC?
I checked below code, I see that "Perform calibration before the reading is taken if requested.", it will trigger calibration...
I am developing a product for a customer using NRF9151(ncs2.7.0, modem fw: mfw_nrf91x1_2.0.2). While verifying it on the DK board, I discovered an issue. When the system starts...
Hi!
I'm writing new firmware for the nrf54 family, and I want to have a system timer with 1s resolution (clock). This clock will be occasionally synchronized with epoch...
I am currently working through the Nordic Academy - SDK Intermediate Course - Lesson 2 Exercise 3, found here:
academy.nordicsemi.com/.../
I am not seeing any of the...
Hi,
Going through the nRF Connect SDK Intermediate course on Lesson 2 exercise 2 step 9 there is a command ncs_install_path/PathToToolChain/opt/zephyr-sdk/aarch64-zephyr...
Hi,
I've recently brought up the Matter Test Harness on a Raspberry Pi following the instructions in the CERT tool repository ( https://github.com/project-chip/certification...
I know the default answer is no, stopping nrf24 and get a RF52 or nRF53 series but my question is about an existing product. We are not all FORD, we can not just do a mass...
Dear Nordic Support Team,
I'm currently working with your Flutter library, mcumgr_flutter version 0.4.1, to implement Device Firmware Update (DFU) functionality. However...
