Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi, I am trying to understand periodic advertising and some basic questions:
I am using periodic_adv example from the NCS.
I see teo ADV data defined in the file as...
NCS 2.7
NRF52840
SPIM3 at 32 MHz.
I have CONFIG_NRF52_ANOMALY_198_WORKAROUND=y and have confirmed the workaround is being activated by setting breakpoints in my code...
Dear,
I need to generate a pulse signal on one IO following this pattern: HIGH for 12us ; LOW for 106us ; and so on...
I tried to use TIMER0 with NRF_TIMER_EVENT_COMPARE0...
Howdy,
I am using an nRF52840 to perform BLE communication. For this communication I am using extended advertising to perform most of my data transmission. Thing is though...
Hello, i have a device supporting DFU OTA i'd like to create a small tool for flashing firmware from the computer to the device. I've set thr device to DFU mode. Is it possible...
I just got a PPK2. I was able to use it perfectly with Power Profiler. Great tool! Today I wanted to learn more about nRF Connect other applications. (Actually I was looking...
Hi there, I'm having so much trouble trying to get this two nRF9161 DK to communicate using SPI, being one Master and the other one Slave. I'm using the spi3 driver for SPI...
We had three nRF52840DK boards (PCA10056) for several years for use in development. Then one died (or to be fair, I killed it), so we got two more that turned out to be newer...
While using nRF Connect, I encountered an error when attempting to enter Debug mode with RTT active. Here are my J-Link specifications and log details:
When I have...
Hi folks,
I am using zephyr sdk version 2.7.0 with a custom board that integrates a nrf52832, an ens210 sensor for temperature and humidity and lis3dh sensor for accelerations...
Hello,
using nrf5340 audio sample present in SDK v2.9.0, I can't hear anything from my nrf5340 Audio DK
I'm testing unicast_server scenario using a Motorola Edge 50 Pro...
I would like to know how efficient it is in terms of power to use UART via the async UART API. Does power consumption differ when its receiving data vs when it is idle? Also...
Hi,
I'm required by FDA regulation to have an SBOM for my project,
I found online that Nordic supports a sort of software bill of materials in the following link: Software...
I have app that's using MBedTLS and offloaded sockets on the nRF9160 modem. I'm using NCS 2.9.0 and it appears to me that it's not possible to set CONFIG_MBEDTLS_USE_PSA_CRYPTO...
