Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Dear nordic,
I am currently working with nRf52840. For designing antenna is there any role for dielectric layer thickness and conductive copper layer thickness
Hi all, I'm testing quick connections and communications using multilink(nus). I am using multilink central example in nrf52832(Central : softdevice v2.0.0 & SDK v11, Peripheral...
I am trying to measure the power consumption when transmitting data from an external device to nRF 52832 to a smartphone.
I am trying to measure the power consumption of...
Dear, I'm designing a PCB with nRF52832 and I will intend to use DCDC converter therefore I putted the two inductors (10uH and 15nH) between DCC and DEC4 pins. The same hardware...
Hi,
I am developing a project in IAR Embedded Workbench for nRF52840-Preview-DK. I have integrated different modules (ble, ADC, SPI, I2C) in this project. I don't have...
I like to integrate the nRF54XXX with a LNA/PA combo (skyworks RFX2401C or 66110). Could you please tell me which pin should be used to control the RFX2401C TX/RX? Which has...
Hello all,
I am currently working on a project to control a door lock and use ble_app_multirole_lesc as reference.
As measurement the current consumption is around 6.5mA...
Hi, I’m working on low power wireless sensor network. I have a big dilemma in choose of wireless mesh solution. Maybe firstly, what i need: 1. Support for low power devices...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the static key feature. But every time when I configure the static key including letters...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the static key feature. But every time when I configure the static key including letters...
Hi,
I am trying to connect to a device while service discovery for another device is running, this is needed to go through connecting multiple devices as fast as possible...
Hi
I am using the light controller and added zb_nlme_permit_joining_request to allowing devices to join the network.
I get a good ZB_ZDO_SIGNAL_DEVICE_ANNCE signal and...
In mesh2.1.1\examples\light_switch\proxy_server I find this flash_manager.c file.Its purpose is to store/resorre/remove DSM&access data.
My flash function referred to access...
Dear Team,
I hope you are doing good......
i am using nrf51822 Device, the SDK version is 12.3.0 in the windows pc with keil version 5.26.
Here i am planning to send...