Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
I just fired up our most recent custom boards with nRF9161-LACA's, and tried to compile modem shell application for RTT.
I noticed the RTT is disabled because HAS_SEGGER_RTT...
I am working nrf52840 with bg96 modem, i have configured quectel_bg9x.c driver to communicate with bg96 modem from nrf52840.
can you provide a sample application on MQTT...
Hello,
I'm experiencing an issue integrating a freestanding Zephyr module with the sysbuild system. The module defines custom boards and projects. When I use the...
Hi
We are the Manufacturer of Smart lighting
We have start new project" Cellular gateway".
We are evaluating the nRF9160 Dk board .
During this we found issue . it...
Hello,
I have 4 nrf52840, 3 act as peripheral and the last is the central.
The peripherals are identical hardware with various sensors using the same FW. I order to...
SUMMARY
Attempting to OTA the nrf52840dk over BLE.
I was able to perform most of the steps in this sample: https://docs.nordicsemi.com/bundle/ncs-2.1.4/page/zephyr/samples...
I have a photodiode, and under indoor lighting conditions, the reading on the oscilloscope is about 150mV. When I connect it to an Arduino Uno or Adafruit nRF52840 Sense,...
I built an application on the NRF52 Development Kit.
I was using the old NRF serial application with the retargetio.c file to push data out through the serial port.
I...
I have been looking at BLE with the Nordic products from the perspective of someone who gets a hand wave of an idea and moves forward. I have developed Nordic firmware but...
We have been able to enable coded phy with PAWR using
```
struct bt_le_adv_param *params = BT_LE_EXT_ADV_NCONN; params->options |= BT_LE_ADV_OPT_USE_IDENTITY | BT_LE_ADV_OPT_USE_NAME...
Hello,
I'm using nrf52840 DK to test 1khz tone. The nRF Connect SDK version is v2.6.0.
I put a pcm raw data array of 1khz tone in the code and used i2s write to send the...
Hi everybody. Recently, I've spent nRF Connect SDK Intermediate online course. I could add firmware upgrade ability using FOTA and now, I can update the firmware using nRF...
Hi Nordic Semiconductor Expert,
I would like to measure the BLE throughput over nRF52805.
Seeing BLE Throughput sample in nRF Connect SDK below, this SoC platform is...
I am developing with the nRF5340, but I am encountering an issue where CONFIG_BOOTLOADER_MCUBOOT is not being enabled. Although I have enabled it in the prj.config file as...
Hey, I am trying to run F8100 development board with nrf52840 development board, while I make the connection simply like CS-D10(Arduino pin layout presenting), MISO- D11,...
