Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello guys!
I have a strange problem where the nrf9151dk suddenly won't power up. It was working fine - I was only working with SW, not HW.
I got a pop-up error saying...
Hi Noridic team,
I have enabled Matter over Thread on the nRF5340. In this setup, I'm planning to reduce the TX power by setting CONFIG_OPENTHREAD_DEFAULT_TX_POWER=0. Apart...
Hi,
I have a question about FOTA jobs with queued and failed devices.
Let's say I am managing a group of 10 cellular devices (nRF9151) through the nRF Cloud UI. I create...
Good day,
I am currently working on a project involving the nRF54 series and would like to inquire about support for the NEC infrared (IR) communication protocol. Specifically...
I'm testing my code based on nrf5SDK v17.0.0 with nrf52832 board.
By nrf connect application,I can see the broadcast packet from my board.It looks something like this. ...
Hi I'm working with nrf5340 dk. I have a serial app (on windows) that is doing serial write continuously to the nrf5340 dk but it is not capturing all the data that I'm sending...
Context
We are working on a project that implies advertising and scanning extended advertised packets.
details :
NRF52840
Zephyr SDK 17.0
Zephyr 4.0.99
NRF SDK...
I am trying to port code I developed on the NRF52 DK to a MDBT42Q-512KV2 BLE module from Raytac I purchased from Digikey and am running into problems.
I developed all the...
Hello,
I'm working with a custom board, using an nRF5340 (NCS v2.7.0 but also tested with version 2.9.0) and a W5500. I'm trying to run the DHCPv4 client test just to verify...
Dear Nordic company,
I have question connected with nrf9151 chip. I know, that this chip contains two parts, ARM core and modem.
I am trying to understand of Serial...
Is there a sample app that uses the Zephyr Light CTL Bluetooth Mesh model? I've tried to add that model to the light_ctrl sample app, but get a crash during configuration...
Hi,
The nRF Connect Extension on my Windows VS code doesn't load altogether:
I uninstalled VS code - including all it's settings/extensions etc using this post's suggestion...
Hi,
I can build and program the broadcast_source sample application using the Python script:
This runs fine and broadcasts as expected. However, I cannot get the application...
Hi, I'm working with the nRF9151DK and Zephyr RTOS (v3.7.99 / NCS 2.9.1) . I’ve configured UART1 to send and receive data via GPIO pins:
TX: pin 8 (P0.08)
RX:...
