I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I noticed on my custom PCB that pairing stopped working, and was getting "reason 0x13" as the disconnect. This disconnect reason I believe is from the phone disconnecting...
Hello everyone,
I’m working with an nRF52840-based board (XIAO form factor) and facing an issue related to USB enumeration and DFU mode detection during development.
Board...
Hi there,
I am considering using one of the npm1300 LDOs to supply 3.6V to the battery backup pin of a uBlox MAX-M10 module using a 100uF capacitor as energy storage for...
HI,
I am using an nRF52840 DK as a Bluetooth LE sniffer and have followed all the steps described in the official documentation .
In Wireshark, I can see “nRF Sniffer...
Hi Nordic team,
We have used shell example of Zigbee sample to connect to an end device. We want to extend the FEM feature of nrf54L05 for this example. We have already...
I want to implement dual-mode operation of LORAWAN and BLE, but when using the SoftDevice, the interrupt on the LORAWAN DIO1 pin does not trigger. I suspect it is being blocked...
Hi,
I have a question after using the DMIC example on the nRF5340:
how do I adjust the PDM clock frequency to 1.28MHz, or how can I achieve this by changing the value...
hello Nordic
i am working with nrf 52840 and 52832. using ncs v2.8.0
i am saving a coredump to flash partition and i am using gdb server - client to try to parse the coredump...
Hello,
I'm migrating an ANT+ BPWR application from **nRF5 SDK** to **NCS v2.5.1** but cannot install the sdk-ant module.
**Background:** - Previously used nRF5 SDK with...
Hello,
I send a ticket because I have an issue to access and write files to a SD Card with NRF54L15DK and 3.1.0 SDK and toolchain.
Can you help me please ?
Here is my...
Hello,
we are trying to run Gazell samples on the nRF54L15-DK, but the protocol & board combination doesn't seem to be supported by version 3.2 of the nrf Connect SDK...
We would like to synchronize several Nordic thingys 53. The Approach is to send two timestamps from a central to them (peripheral) via Bluetooth Low Energy with 100 ms delay...
Hi
I try to start with ST7789 display on nRF54L15 and there are bus fault after add LVGL library. The project is building correctly, but stop just after leave bootloader...
Hi,
I accidentally opened and subsequently programmed the PPK-II in Bluetooth Low Energy module startup. The programming didn't complete but resulted in an error. Now...
