Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hello,
I am trying to program my nRF9160 DK v0.9.0 with mfw v1.1.4 but I am getting an error "Modem DFU failed with error: Error: Error occured when program. Errorcode:...
Greetings,
I have two nRF52840's where one is modeled as a peripheral and the other as a central. I have created a custom service and characteristics on the peripheral...
hello Nordic
i work with nrf52840, SDK16.0 S140
i use QSPI for writing to an external flash (IS25LP064A)
if i write 16 bytes then its all ok but if i try to write...
Hello,
I have nrf52810 with soft device S132 5.1, SDK 14.2.
It works fine when NRF_LOG_ENABLED is enabled, data from NUS are printed in debug console. But Im not able...
Hello,
I am writing a BLE central application that connects to a device and should then discover ALL services on the device. I am new to Nordic and am using the nRF5340...
Hi
I am going to start an application with the mesh network. Here is my requirement,
1. I have to receive the data from the master device (STM32) by using SPIS (nRF52840...
Hello,
I am using the ble_app_uart_c_pca10056_s140 example code (SDK v17). This is the NUS BLE central device.
The code is almost unchanged from the example source.
...
I'm quite new to nrf.
These days I'm trying to program power efficient uart data sender over ble.
It receives uart and sends data fine.
The problem is it's not going...
Hello,
Does nRF52833 has support for FreeRTOS in version 16.0.0 of nrF SDK?
Is there any specific example with the softdevice and FreeRTOS?
Thank You,
Vineeth...
When we develop out product, we found it cannot connect to our server. After our check step by step, we found if we comment the code about RAI setting, MQTT service can be...
I wanted to add TWI functionality to the flash fds example and was confused about adding drivers with CMSISwizard. I manually added all the necessary twi drivers based off...
HI
I have got a new nrf5340 DK. I have tested four LEDs and HRM. It's working fine. But when I have tried to upload blinky or hello_world Sample from NCS v1.5.1, I can't...
Hi all,
I have tested successfully the wireless timer syncronization proposed by:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts...
Hello guys.
I recently discovered that you included example codes for OSDP Control Panel (CP) and Peripheral Devices (PDs). In NCS v1.5.1 that I am using, they can be fund...
