Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I'm using this example of code (nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader\pca10040\dual_bank_ble_s132\arm5_no_packs) with my custom board to perform a dfu....
I have a peripheral device based on the nRF52832, using SDK 15.3.0. It uses a bunch of the standard services, including the TX Power Service, plus a custom one. When I connect...
What would be the best example to start with if i have to send the sensor data from nrf52840 to a mobile application using SDK for mesh? I have asked this question before...
Hi, could you tell me where I can find a sample project with button-less DFU-OTA and an application like ble_app_gls?
1. I use Windows 10; Embedded Studio; nRF52840 DK;...
Hello, We are using the NRF52840 and softdevice S140, PCA10056 on all examples. SDK version is 15.3. We see a problem following the secure OTA DFU protocol regarding acessing...
Hi,
I'm developing and testing the code using the PCA10040, but this board uses the NRF52382_XXAA which contains more memory and I want to use the NRF52382_XXAB. So, how...
Hello guys,
I have coin cell powered nRF52832 based sensor node. I develop the firmware in Segger Embedded Studio, SDK15.3.0.
On the pressure of a button on the sensor...
Mesh SDK:3.2.0
I want to send dimming level to server, and want return data of dimming level with mcu voltage.
When I receive server set callback, I tried: status publish...
I am developing a beacon-related project, my nrf51 device needs to play beacon. Beacon will determine the distance from NR51-> Smartphone. If distance = distance I give, I...
Hi all.
I am using a nrf52840 with mesh sdk 3.20 and sdk 15.30.
I am implementing RSSI tracking and require reference nodes to advertise once on each channel (37,38,39...
Hi guys,
I am using nordic semiconductor nrf52840 development board and segger. Is it possible to display the data of ultrasonic sensor on the nrf connect app by configuring...
Esteemed Colleagues,
We are using PCA10040 (1.2.4 2018.16) to develop a customized NFC Type 2 TAG. SDK 15.0.0 was used because we needed to work with hal_nfc_t2t.c instead...
Hi Team,
I am developing a low power application where we need to update Firmware frequently based on use cases.
I have successfully tested BLE secure DFU example and...
Hi,
We're trying to characterize the radio timings of the transmission of a Bluetooth Mesh packet from an originator in a Bluetooth Mesh network. Looking at the broadcast...
Hi,
In your nRF5 SDK v16.0.0 release note, I recognize that a new feature is added:
I am wondering which BLE event is indicating that SD has been free from BUSY state...
