after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
The provided ble_app_template10056e from nRF5_SDK_17.1.0_ddde560 crashes:
The crash was reproduced using:
1. nRF52 DK Kit - ( https://www.nordicsemi.com/eng/Products...
Hello,
Can anyone know how to print MCUboot info on serial debug terminal or Normal Debug terminal using COM port?
What are the Configurations to be added for this?...
Hi guys
I am working on a project need to pass the ADS1231 read data through BLE. But I haven't done so far. I just try to read the ADS1231 value first. Referring to some...
I see an example of a central device and peripherals as one, and I see it using the following three registers to determine the start or end of the broadcast, the beginning...
As stated in the title.
I am using nrf52832 provisioner example with light_lightness example in v4.2.0. Provisioner is able to set up the network with clients and servers...
Hi support team,
We have a new project now. We plan to use nrf52832 for the project. We know about the BLE and the related development, but we are not familiar with nordic...
I am using C++ to program the nRF52 DK and I am trying to use the standard vector library.
When I try and compile it I get the linker error:
${GCC_PATH}/arm-none-eabi...
Hi I am trying to do the led blinking in nrf52840 but the led is not even turning on i have given the code below can any body help me out.
nrf_gpio_cfg_output(14); nrf_gpio_cfg_output...
Hello,
I was able to create a mesh network with two nrf5340 boards configured with the mesh light sample and the mesh light switch sample.
I am trying to substitute...
I recently purchased a Thingy 52 with the goal of processing the the raw magnetometer, accelerometer and gyroscope data using a sensor fusion algorithm to determine orientation...
Hello, We're about to start a new project with the nrf5340 as our SoC. When reading the docs for the nrf5340 ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
I have problem with wakeup of Low Power Node from System ON sleep mode. In debug session code works as expected, however outside the session something gets wrong.
The node...
Hi,
I'm trying to create an application based on the SMP Server app (NCS v1.7.0). I'm able to perform a FOTA using nRF Connect for Mobile and the app._update.bin without...
