after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I am developing using the SoftDevice s140 7.2.0.
I am trying to use the MBR function sd_mbr_command() to upgrade my bootloader with command SD_MBR_COMMAND_COPY_BL...
I followed all the steps from the readme instruction and struggle at:
## Compiling pc-ble-driver from source
Step 1. Install vcpkg dependencies is running succesfull ...
I have an example for board PCA10040 that I want to use on a custom board. It is described on nRF5_SDK_v17.1.0/nrf5/sdk_for_custom_boards.html that I have to (1) create a...
I have two Adafruit feather with nRF52832 on them, using one as central and the other as peripheral.
I have created some codes based on ble_app_uart from Nordic SDK and...
Hello,
I'm trying to program the NRF5340 DK board on linux. However, the board doesn't show up when I run `nrfjprog -i`. It doesn't show up when I run lsusb. `udevadm monitor...
I'm struggling to get a Micron MT25QU128ABA ( https://media-www.micron.com/-/media/client/global/documents/products/data-sheet/nor-flash/serial-nor/mt25q/die-rev-a/mt25q_qlhs_u_128_aba_0...
Dear Community,
We want to use bonding to connect our app to the nRF and create a personal account.
So all your devices will have the same UUID. If the device never connected...
We're working on a board with an nRF52840 running BLE with softdevice S140 and SDK 17. The board has an external SPI flash, and when we realized that SPIM3 can be run at higher...
I want to know if I call the following function, which condition should I meet to determine that the coordinator is not connected to any terminal devices. For example, I now...
Hello, I am looking for some help or example code that describes minimum set of the files and #defines required to enable AES 128bit encryption and decryption using ECB mode...
Hello,
I'm trying to learn what might be typical latencies for Bluetooth LE Audio. For instance, the aptX low latency codec claims latency around 20-40ms. Is Bluetooth LE...
Studying the documentation for the nRF52811, I found a difference in the description of memory recording and memory erasure:
write: " The CPU is halted while the NVMC is...
Hi,
I have nRF52840 DK and am using nRF5_SDK_17.0.2_d674dde.
I am not using SoftDevice, and Zephyr RTOS.
I have a simple program and using RTC0 timer. My code snippet...
