Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Do you give us some software workaround to use SPI (P2.08-MISO, P2.09-MOSI )
The Hardware design refers to datasheet v0.9, connecting P2.08 as MISO and P2.09 as MOSI. From...
Hello,
we are testing the openthread CLI example on nRF54L15dk
We have compiled it with the following options:
CONFIG_OPENTHREAD_CHANNEL_MONITOR =y
CONFIG_OPENTHREAD_CHANNEL_MANAGER...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
Hello, I’m working with the Distance Measurement (nrf_dm) module and aiming to implement a centralized topology using Anchor and Tag roles.
The intended behavior is:
...
Hello,
According to my understanding of Bluetooth Core Specification 6.0, Volume 6, Part H, "Channel Sounding", it is not a requirement that the Initiator and Reflector...
Hi NRF support team, We are developing a custom board based on the NRF9151 SIP. I am experiencing some issues in provisioning the device to the NRF cloud. On the 9151-DK i...
Hi,
We develop functionalities on native_sim before moving to embedded, therefore I am trying to have nRF9160 modem connected to Zephyr "cellular_modem" sample on linux...
Currently, as a peripheral, I can discover services like GAP and GATT on the host. However, I'm encountering issues when trying to discover the ANCS service. When calling...
Hey All,
Last month a network provider had some internal issues which rapidly started rejecting our devices with several EMM registration issues, however due to not seeing...
Hello All,
We have developed a Zigbee End Node device for which we would like to make a radio test.
we are using nRF connect SDK 2.0.0, please note the reason we use the...
Hello Nordic Team,
I’m currently working with the nRF5340-DK and nRF Connect SDK (v2.6) using VS Code . I’ve been testing OTA firmware update processes using MCUboot and...
Hello
I need help, I have a problem implementing ppi gpiote and spim. The ADC I use is mcp3562 which sends via the irq pin when the data is ready. I need to work in continuous...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
Hello I have an nRF52840 board with a 2 MB external flash I'm using SDK 2.6.2 I'd like to configure the mcuboot_secondary partition to be on the external flash
Here is my...
Hi,
I'm about to develop a custom board with nRF52840 IC. For a first test I need an external antenna. I modified a dongle for a first proof of concept. I removed the antenna...
