after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I am working on a project that involves 2 nrf52840 DKs. One device will be running a ble application while the other device will be lookin, fetching and programming...
In SDK 1.4 we combined the udp and GPS examples and the result is unstable.
I think this could be because once enabled by RRC mode == Idle, GPS keeps going forever.
After...
Hi,
I have an issue with using the %XRFTEST command for TX testing on the LTE-M network. My setup consists of the nRF9160 DK (PCA10090) with the MFW 1.2.3 and a 1NCE SIM...
hello,
i am using two customised nrf52840 boards to get maximum range between the boards using this example https://github.com/NordicPlayground/nRF52-ble-long-range-demo...
I have update the SDK from version 1.4.2 to 1.5.0.
Suddenly i see that the hci_rpmsg is not build as a child image.
Which defines do i need to set for that now?
Hi,
Currently, we work on a project that uses:
nRF9160
Zyphre OS
Segger Embedded Studio for Arm (Nordic Edition) V5.10d
SDK v1.4
CONFIG_NEWLIB_LIBC=y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Hi Team,
I am trying to build a project for nrf52810 and I selected an example project from the below given path.
nRF5_SDK_17.0.2_d674dde\examples\peripheral\blinky\pca10040e...
Hi, I've been working with the nRF9160 and at some point the logs normally displayed in LTE link monitor were gone. I've tried re-installing the Link Monitor but it didn't...
I'm trying to merge the ble_Central example project with ble_app_template project. I've added 3 Custom services in the ble_app_template project by setting UUIDs and trying...
Hello,
I am working on a nrf52833 custom board. Most of the time, the system stays in sleep mode, and periodically sends bursts of data via SoftDevice.
I try to configure...
I am using bootloader based on Nordic secure bootloader example. I would like to add possibility to identify device after entering BLE DFU. I was thinking about device MAC...
Device : nrf52840
Platform : baremetal
Peripherals in use :
Softdevice
FDS
SAADC
RTC
I am using FDS Library to Write Data whenever an event is generated...
