after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I'm trying to convert the NCS - cloud client sample to connect to AWS_IOT rather than NRF cloud.
After a connection achieved, i press Btn1 and I get the following...
I believe I am having a very similar issue to devzone.nordicsemi.com/.../dfu-from-external-flash-using-spi-nor
I posted this as a new thread to avoid high-jacking that one...
Hi everyone,
I am working on USB MSC example . I have two questions.
1. What is the MSC_WORKBUFFER_SIZE defines in the example? Is the last parameter of APP_USBD_MSC_GLOBAL_DEF...
My issue seems to be similar to DRGN-12539. However, I am erasing internal flash.
I am calling in a loop nrfx_nvmc_page_erase to erase multiple pages of flash. At first...
I am building a custom boot loader to work with out application on a custom board based on the UBLOX NINA-302 module. The boot loader will use USB as the only connection and...
Hi.
I'm trying to read data of MAX30102 using TWI, it has 8 bits of data in the FIFO_DATA register.
The library I'm using for data extraction and processing was written...
Hello,
I am using the nRF52 DK with Segger Embedded Studio and the SDK 14.2.0. I wanted to build the example 'esb_ptx_pca10040' with logging enabled. To achieve this, I...
Hi,
I'm using the S132 on the PCA10040 with the external XTAL disconnected (SB1 and SB2 cut)
In order to check to if the external is present I call nrf_sdh_enable_request...
I am working on my first BLE project for my employer and have been unable to connect over BLE to our custom board with the nRF52840 processor. To eliminate issues with my...
I received a nRF9160-DK and was looking at working with zephyr/boards/shields/x_nucleo_iks01a3 but my x_nucleo_iks01a3 shield will not plug into the nRF9160-DK (DK) it seems...
I have setup a small thread network (1 FTD Router, 1 Border Router, 2 MTD Dongles) using the Nordic provided RaspPi border router image.
I have been attempting to get Thread...
In my custome PCB design, I am using the CHIP antenna , the same used in nRF 9160 DK, that is P822601 from ethertroncis. Can this antenna work for GPS too? If not can you...
