after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
So, we are using NRF52811 with external 32MHz xtal and also exeternal RTC crystal.
Every now and then we are unable to pass tests of the programmed firmware because the...
Dear Sir/Madam,
I have already developed an RF communication device with an NRF24L01+ device. And I want to migrate to nRF52833-QIAA-R. For that, I have the below questions...
I'm using RTC to wakeup every 500ms, I have Watchdog enabled but after a while (about half.. or an hour...) it will not wakeup anymore and watchdog will not reset.
I measured...
Hi, we programmed the nRF52840-DK with ble_app_hids_keyboard demo (s140) and tested with different BLE keys under a Linux PC. It worked. Tested the same configuration with...
Hi,
I have some code that normally uses nrf_crypto with the cc310 or cc310_bl backend. I was writing a unit test for this code which compiles and runs in Linux/WSL. Since...
Has anyone written a utility to dump the tables of contents (i.e. directory of files) and
an entire file with record keys:contents to a host operating system file to a file...
Hi,
I'm working on the bootloader part of a project. Using nrf Connect, the integrated MCUBoot bootloader, trying to figure out how all the parts fit together. Running into...
Hi,
As iOS developer, I'm facing a really strange issue : Using the nRF Connect app, I try to connect my BLE device, with success or not depending my iPhone/iPad configuration;...
Hi guys,
I am using the nRF52832 board on which I run the LPN example from BLE Mesh directory. I put there the code for measuring the temperature and now I want to save...
Hi ,
How do customers choose printf lib when they want to use floats on functions printf and scanf?
The customer wants to use floating points
However, the current printf...
I want to use nRF Connect v3.6.0 Programmer and Segger J-Link Ultra+ in order to program our board. I can connect to the J-Link but receive an error message:
The Segger...
Hi Nordic team
Current https_client example at sdk connect
Connect to server --> send http request to server --> Wait response from server
Can we receive packet from...
Hello,
After a long investigation I got to the conclusion that SPI master (spi3) has been broken in the SDK version 1.4.1.
It is working fine in V1.3.1
I have an application...
Hello,
I'm using SEGGER Embedded Studio 5.30a with NCS 1.4.99.
I'm trying the "hello_world" sample but when i want to run on the nRF5340DK i get the followings errors...
Hi,
I am using FDS for read and write the records with SDK17, My code is working fine but when I change the optimization level 2 for size then I am getting FDS_ERR_UNALIGNED_ADDR...
