Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I was playing with my development software in VS Code everything was OK apart from the Cmake error message.
Once I had to restart my computer I couldn't build my...
Hello team,
We are developing a custom board on which eSIM is used for cellular connection. We will use Serial LTE modem application to control cellular modem through...
Hi,
I am using the nRF5340 Audio DK board with the nRF5340 Audio application under NCS v2.8.0 as a Unicast client.
I observed that changing the connection interval to...
Hey everyone,
We have been struggling to get our nRF7002DK connected to any HTTPS server. We've stripped back our evaluation setup to use "google.com" with the example ...
Hello,
I wanted to verify if two devices are communicating by using a sniffer.
After running the radio_test example, I set up parameters for each transmitter and receiver...
Hi,
I just reinstalled a fresh version of VS Code 1.96.2, and I'm using v2024.12.55 of the nRF Connect for VS Code extension. I'm also using nRF SDK v2.1.1.
In the past...
Hello,
Version - nrf Connect SDK v2.7.0
We have our own project which, I believe, has correctly configured signing using a custom key file.
In VSCode I've created a...
Hi Nodic support team.
Can i know which usb example we can use to modify to usb bulk application in nRF52_sdk_17.1.0?
1. nRF5_SDK_17.0.2_d674dde\examples\peripheral\usbd...
I refer to and the answer answer given by AI referring me to you.
I need the lithium battery only to about 8-bit accuracy to reduce the leakage current. Please provide...
Hi,
I'm new to fuel gauging and battery profiling and am trying to understand the process and the parameters used.
Is there a description of how a battery model is created...
Hi all, I want to program a nRF5340 microcontroller to become a peripheral BLE device. I use the Zephyr with nRF Connect SDK 2.7.0 and VSCode as IDE. I have a custom electronic...
After updating my nRF Connect Command Line Tools to version 10.24.2 on my 2019 Intel MacBook Pro 16 running Sonoma 14.4.1, I've encountered an issue where the Flash action...
Hello!
I have an issue with the nRF5340 when using it with an M1 MacBook Air. When I connect it to the laptop I get a notification about JLink ejecting every few seconds...
Hello! I need to post, but can't since december, why?
I have updated Windows 11, SDK 2.6.1 and 2.8.0 default is 2.6.1
Board SDK nrf9151
I need to use http_client or...
