Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I just fired up our most recent custom boards with nRF9161-LACA's, and tried to compile modem shell application for RTT.
I noticed the RTT is disabled because HAS_SEGGER_RTT...
I am working nrf52840 with bg96 modem, i have configured quectel_bg9x.c driver to communicate with bg96 modem from nrf52840.
can you provide a sample application on MQTT...
Hello,
I'm experiencing an issue integrating a freestanding Zephyr module with the sysbuild system. The module defines custom boards and projects. When I use the...
Hi
We are the Manufacturer of Smart lighting
We have start new project" Cellular gateway".
We are evaluating the nRF9160 Dk board .
During this we found issue . it...
Hello,
I have 4 nrf52840, 3 act as peripheral and the last is the central.
The peripherals are identical hardware with various sensors using the same FW. I order to...
SUMMARY
Attempting to OTA the nrf52840dk over BLE.
I was able to perform most of the steps in this sample: https://docs.nordicsemi.com/bundle/ncs-2.1.4/page/zephyr/samples...
I have a photodiode, and under indoor lighting conditions, the reading on the oscilloscope is about 150mV. When I connect it to an Arduino Uno or Adafruit nRF52840 Sense,...
I built an application on the NRF52 Development Kit.
I was using the old NRF serial application with the retargetio.c file to push data out through the serial port.
I...
I have been looking at BLE with the Nordic products from the perspective of someone who gets a hand wave of an idea and moves forward. I have developed Nordic firmware but...
We have been able to enable coded phy with PAWR using
```
struct bt_le_adv_param *params = BT_LE_EXT_ADV_NCONN; params->options |= BT_LE_ADV_OPT_USE_IDENTITY | BT_LE_ADV_OPT_USE_NAME...
Hello,
I'm using nrf52840 DK to test 1khz tone. The nRF Connect SDK version is v2.6.0.
I put a pcm raw data array of 1khz tone in the code and used i2s write to send the...
Hi everybody. Recently, I've spent nRF Connect SDK Intermediate online course. I could add firmware upgrade ability using FOTA and now, I can update the firmware using nRF...
Hi Nordic Semiconductor Expert,
I would like to measure the BLE throughput over nRF52805.
Seeing BLE Throughput sample in nRF Connect SDK below, this SoC platform is...
I am developing with the nRF5340, but I am encountering an issue where CONFIG_BOOTLOADER_MCUBOOT is not being enabled. Although I have enabled it in the prj.config file as...
Hey, I am trying to run F8100 development board with nrf52840 development board, while I make the connection simply like CS-D10(Arduino pin layout presenting), MISO- D11,...
