after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I try to add a custom signature key to the nrf5340_audio application from NCS2.7.0. I cannot use an absolute path because the project must be build-able by different people...
Hi,
I am carefully assessing the life cycle cost to define my strategy of launching 4 product models in the market by next year that they are in design stage at this moment...
Hi all!
I am having trouble intalling the nRF Connect SDK in my Windows 8 computer. I'm currently following the installation steps specified in the nordic course https:...
Hi,
I am currently working on a project using the nRF52832 as my controller. During development, I realized that both BLE central and peripheral roles are necessary. I searched...
Hi,
I am currently working on a project using the nRF52832 controller as a gateway device and the nRF52810 controller as a timer indication device.
I have successfully...
Hello,
I am a student currently studying Bluetooth Low Energy (BLE).
I am working with two Adafruit nRF52832 boards (Adafruit Feather nRF52 Bluefruit LE - nRF52832, link...
Can nRF51822 be used as uart BLE peripheral together with nRF52832 (as uart BLE central)? If so, are there any examples? So far I can find only uart ble example for nRF52832...
Hello, in a video by Ai Kevin of Nordicsemi sharing about ESB development, I learned that the ESB can be specially configured to work with Ellisys Bluetooth Explorer for packet...
Hi, Is it possible to use the same UART instance for app core and net core to put the log messages? I am using an nRF5340DK board, which uses a separate COM port for each...
Hi,
My phone can find, but is unable to connect to, the FastPair locator_tag example. I have made no changes to the example code.
The most relevant error I can see in...
I would like to reduce the power consumption in normal operation mode.
Then I would like to reduce the operation frequency in the I2C, SPI and UART.
What is the command...
Hello everyone,
I’m trying to set up an nRF52840 dongle as a Thread radio co-processor to integrate with my Home Assistant setup. I followed the instructions in this Nordic...
Hello!
I have a device on which the S25HL01GT memory is soldered. The problem is that I don’t understand how I should work with .dts in order for this memory to work with...
Hi,
I started fesh on a new laptop, installed nrf Connect for desktop. I used VS Code to install the the latest nrf toolchain and sdk, verison 2.6.1, as they recommend that...
I create a linux docker container about nrf development environment. And the container host is windows11.
everything works fine except flashing function.
i passthrough...
