Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi ,
NRF54L05 how to surpport CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC in bare-metal SDK,and while enable mcuboot OTA DFU feature ,how to modify the configuration?Thanks.
Hello,
It was possible to activate the Window covering sample to control opening or closing with nRF5340-DK Button 2 and 3.
Button 1:
Depending on how long you press...
Hello,
I am developing a Bluetooth Mesh application using Nordic hardware and am running into reliability issues when transmitting bursts of vendor messages.
System overview...
Hi, you all.
I am working on the DFU system with my custom BLE service. I have successfully integrated DFU into my system. I structured a system with integrating DFU into...
Hi all,
I am trying to get going very simple connection between multiple devices - specifically the end product is first-responder walkie-talkies. Effectively all I need...
I'm working with NRF54L10 module. I needed more mcuboot space so in pm_static.yml I allocated it 80kb. Before this FPROTECT was working but after I allocated 80kb, now FPROTECT...
Hi, I am using VS Code with Extension Pack for nRF and nRF Connect SDK Toolchain v3.2.1 and trying to build the environment for working with the dect_shell sample. nRF9151...
Hello all,
I'm using ble_wifi_provisioning example.
I need to save the phone pairing. I added the definitions as described here: https://academy.nordicsemi.com/courses...
Hello,
I am planning to conduct R&D on Bluetooth Low Energy (BLE) with PAwR (Periodic Advertising with Responses) and low-power communication techniques. To progress with...
I originally developed the product using the nRF5 SDK with C++. The functionality is already implemented, but due to high power consumption from the C++ version, I now plan...
Sadly not in the documentation and the sizes changes from 5.0.0. I did try using the 5.0.0 but it doesn't boot (could be another problem). Thought I'd ask anyhow.
I have managed to use 3 nrf5340 audio DKs one configured as Gateway and the other two as left and right headsets to stream stereo audio. My question is, what do I need to...
I’m working on an nRF52-based design where the device should remain in System ON low-power mode after an operation (SAADC sampling + BLE sync). After SAADC data collection...
Hello,
My application uses three nRF5340dk for LE Audio: two Unicast Servers and a Unicast Client. The Client scans for servers, establishes connections, performs discovery...
Hello, I'm using the nrf5340 Audio development kit with SDK Manager v2.9.0 and a micro SD card, and when I try to play the audio as indicated in the development example in...
