Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
My task is to implement inbuilt RTC for nordic MCU nrf54l15 series. When i use the below API nrfx_grtc_init, it is throwing a error and returning a error code which is saying...
Hello Nordic Support Team,
I’m working with an nRF5340 using nRF Connect SDK 3.0.2.
I am trying to use the NFC pins (P0.02 and P0.03) as an I2C slave interface. However...
Hi,
I would like to generate a PWM signal specifically on the P0.03 pin of the nRF54L15 using GPIOTE + DPPI + TIMERS.
As far as I’m concerned, Port 0 in nRF54L15 does...
Hello all,
I am trying to run bap_unicast_server example with nrf5340_dk. I used no sysbuild configuration. Then I manually added hci_ipc as it shown at ss
I flashed succesfully...
Hi,
I'm currently working on a project using the nRF5340, and I've successfully configured the I2C0 interface as a static Master in my .overlay file using the following...
Hi all,
I am trying to execute an application in XIP mode from an external QSPI flash on an nRF device (nRF5340, Zephyr + MCUBOOT). The setup is:
Partition file:pm_static...
Hello,
I am using edge impulse library to achieve on-device classification. I now want to put the edge impulse related code to the external flash and use XIP function there...
Dear All, I am facing a rather strange issue with the nrf/samples/wifi/shutdown example. I am working with nRF Connect SDK v3.1.1 and a nRF7002DK board. I am observing the...
I recently upgraded from a Ubuntu raspberry to a Raspery PI5 running PI OS and have two Nordic boards but not able to install the nrfConnect image on the PI image. Is there...
Hello,
We are preparing nrf52832xxAA for certification, Im trying to compile DTM from nRF5_SDK_17.1.0 (same issue on v16.0) Default UART pins run fine without error #define...
Hi, I am trying to migrate my device from s132 7.2.0 to s332 7.0.1, for adding ANT. I have no more access to the SWD. I know it is not tested : docs.nordicsemi.com/.../lib_bootloader_dfu_validation...
I am attempting to integrate the MM8108 with the NRF54L15 SoC as my lead engineer suggested, but now I am finding that it is not that straightforward. We want to make a HaLow...
Dear All, I am developing an application where I need to get the nRF5340 to the low power state, where the chip is consuming less than 10uA when it idle, while using the nRF7002...
I would like to control the RGB LED on the board. I followed the drievr example provided by the nrf sdk, but it doesn't work. As far as I understand, I don't need the signal...
