Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
HI
I am using nRF54L15 PDK with NCS 3.0.0. In my code, I am using NVS to store data on the MX25R64 flash on the PDK. The initialization code is as follows:
struct flash_pages_info...
Hello, I am currently working on a PDM microphone project using nRF52840 and Zephyr RTOS. I've been testing the official Zephyr sample (located at dmicncs/v2.9.0/zephyr/samples...
I have three questions regarding the electrical parameters of the NRF9151 chip:
For a GPIO configured as output: What is the maximum source current per pin when driving...
Hi,Team,
I am developing the nrf54l15-dk, and the version of my NCS is v3.0.2. Because our terminal device 1 does not support using ble-FOTA, I used another terminal device...
Hi,
We have a custom nRF9160 board with chip antennas for LTE and GNSS. They are Ignion antennas with matching circuits customised to our board dimensions. We also use...
Hello, We are developing an application with nRF52810 based on nRF Connect SDK V2.4.1. The application is utilizing the BLE connection, particularly the NUS Service (emulation...
Hi,
I’m testing low-power behavior on an nRF52811 device.
When SoftDevice is not enabled , calling nrf_pwr_mgmt_run() gives me a stable ~5 µA average with no visible...
I am experimenting with ble_app_uart & ble_app_uart_c using two terminal windows, and I am sending a string of 1000 chars from the central to the device.
Although they are...
Hi Nordic
As information of nrf connect SDK, NCS3.0.0 ble_coex sample at NRF7002 DK can share single antenna for BLE and WIFI protocols.
It only needs to set "CONFIG_COEX_SEP_ANTENNAS...
I’m trying to use the Zephyr software split BLE controller ( BT_LL_SW_SPLIT ) on the nRF54L15 DK with NCS 3.0.1. I understand that this controller is not certified, but I...
I have successfully built an Auracast broadcaster transmitter using an nRF540 Audio DK and can stream to a pair of Samsung Galaxy Buds3 Pro with a Samsung Galaxy Tab S11 acting...
Hello, I observed this hebaviour on our own custom PCB with nrf5340: We would like to perform DFU over USB DFU class using dfu-util on the host. We tested our code on Thingy53...
I'm developing a device that occasionally bursts large data payloads (~30kB) over BLE. It uses MPSL to share the radio between BLE and ANT+, so I'd like the BLE radio to use...
Hi!
I'm developing an application that uses the bluetooth object transfer service.
I can transfer the directory list object (using OTS_OBJ_ID_DIR_LIST) from the server...
Dear All, I am developing an application based on the nRF7002DK. I am using nRFConnect SDK v3.1.1. I am producing my own CA, server and client keys to be used for TLS, with...
