Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
The dongle is an excellent piece of hardware. However the features of DFU is rather limited.
I am wondering if I can put two hex files onto the dongle? For example,
1...
We are evaluating 52811/52833 with DF.
1. Is there a beacon example for any of this chips?
2. Is their central example with CTE enabled?
3. Is there example with using...
Hi,
I work with win10 laptop, Toolchain nrf Connect SDK 1.6.1 on a nrf5340dk.
On peripheral_uart sample, I would like to enable uart when a device is connected and I want...
On the nrf connect sdk documentation page there are instructions for configuring a radio co-processor:
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_thread_tools...
Hi,
I wanted to replies to Mister Martin Sivertsen from this post https://devzone.nordicsemi.com/f/nordic-q-a/81235/nrf52840-dongle-external-antenna
I accidently locked...
Please ask a question about "PCB specification" in "nRF9160HardwareIntegrationGuidev12.pdf". The board thickness is 1.6 mm. Adding the thickness of the listed copper and FR...
Hello
In our application (NRF52840, softdevice S140 v7.3.0, master device with multiple connections) we are experiencing some strange behaviour related to scheduling of...
Hi All,
I feel like this question/topic has probably been discussed ad nauseum, but I feel like I'm not confident in the conclusion I'm drawing from other posts I've seen...
How to reject/disconnect peer (smartphone) which tried to write huge data to service? For now in my project (based on ble_app_multperipheral project from SDK) if the smartphone...
Hi Nordic Team,
I would like to understand how the radio test works. A better description of the commandos would also be helpful. Is there a more detailed description than...
Good evening,
The following link to "TIMER HAL" lists various enums, including for example " NRF_TIMER_BIT_WIDTH_32 (alias of) = TIMER_BITMODE_BITMODE_32Bit ". I've used...
On Windows 7 64 after update to 3.8 (and 3.9) nRF Connect for Desktop the Bluetooth Low Energy and Power Profiler can't find device nRF52840-Dongle and PPK2.
What to...
Hello,
I was wondering if I could bypass the protocols related to BLE transmission (GATT/ATT) and utilize the RADIO peripheral in a close to constant TX rate without regard...
Hello!
Short question: How can I pass a parameter to a SW Interrupt?
Expanded question: I want the board to wait for an ammount of bytes comming from SPI, once this is...
Hi all,
i am really desperate. since more than 1 week i am trying to work with the digital inputs in my custom pcb.
I can set all digital outputs, but from the inputs...
