Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
I have been using visual studio code on mac for development, and it started showing error code 63 when I try to start debugging on the 9160 based hardware. It used to work...
Hello,
I am studying the materials in Bluetooth Low Energy Fundamentals.
I cloned the codes from GitHub https://github.com/NordicDeveloperAcademy/bt-fund
I tried to...
Hi,
If you use the following settings, an error will occur during commissioning.
Board: Custom board
SDK:ncsv2.9.2 OS: Windows10 Sample code:Matter Lock bord target...
Hi,
I’m new to working with nRF MCU and I’ve just purchased an nRF52840. I want to use it with my own custom board, but I’m not sure where to start. I would like to use...
We're running SDK v2.6.0 on a nrf5340 processor and initiating a connection to a specific heartrate monitor using the bt_conn_le_create() function. What function do we call...
Hi, DEVZONE,
Can you suggest a proper samples and tell me what are must-have configurations ?
nRF (zephyr) SDK v3.0.1 or v3.1-rc1 versions are preferred.
Also, can...
I'm looking at the example esb_ptx and esb_prx from SDK v3.0.2 running on an NRF5340 and NRF52840 respectively.
This function in esb.c
sets packet_config.flen based...
Hello Nordic Team,
I am writing on behalf of my company, where we are developing a cross-platform application using .NET MAUI . As part of our application, we need to implement...
I'm implementing a feature which requires me to store data in ram region which would not be resetted during reboots (sys_reboot(SYS_REBOOT_WARM)).
I'm using clause in application...
I'm trying to flash an external board using the Ezurio BL54L15 module, with the nRF54L15-DK as the debugger. SWD is connected via the DK's Debug Out header to the module's...
Note: related to
Last week we had an issue regarding camera flash triggering reset and undefined behavior in our nRF52832. We have been able to reproduce this issue in...
Hi Everyone, I'm using nrf9160 sip, mfw_nrf9160_1.3.7 modem firmware version, slm example, sdk v2.8.0. When I include lte_auto_connect() function or manually configure the...
Hi Support Team
We want to use Windows PC to do the BLE FOTA for nRF52840 BLE device. The following DevAcademy exercise mentions that AuTerm can be used to do the FOTA on...
