Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I'm running the SDK 17 radio test example on two nRF52840 DKs. My goal is to do a PER measurement in 802.15.4 -mode.
I configure the boards to use ieee802154_250Kbit mode...
Hi, I am using nrf52832 board. I was trying to disable the GPIOTE interrupt for a particular event (Event4) using INTENCLR register. My code was NRF_GPIOTE->INTENCLR = 1 ...
I am trying to get the nRF9160 DK power consumption down as much as possible to establish a baseline for development. After struggling to achieve the values claimed in the...
Hello,
I am using NCS v1.5.0 and an nRF9160 on a custom board, my application has a custom SPM and the secondary slot for the firmware image upgrade is stored on an external...
Hi,
I'm developing a peripheral sensor and central receiver as a complete set. So I wish the peripheral is only visible(or connectable) to its central device.
I know the...
Hi there!
I wanted to do a little side project that's something completely different than BLE Mesh (which I do for work). I decided Zigbee would be fun. Even more so because...
Hi,
I have an nRF52840 DevKit and dongle and am using SDK for mesh v.5 with SDK 17.0.2.
I want to update the firmware in a mesh network and am working on the mesh DFU...
I am using nRF52832 S132 V7.2.0. I am using ble_app_hrs_c example.
I only set nrf_ble_scan_filters_enable(&s_scan, NRF_BLE_SCAN_NAME_FILTER, true) to scan and match successfully...
Hi,
I am interfacing the Peripheral_hids_keyboard + peripheral_uart code
I code can print all the log info data printk and printf data in uart console
I want to separate...
Hi,
I've been working on the hrs example for nRF52840 DK and I wanted to add buttons to the project. For the first button (I took from app_blinky), it is working perfectly...
Hi,
I got a problem while updating BL using ble OTA DFU.
in NRFConnect App log it is showing as follows
nRF Connect, 2021-07-02
DfuTarg (E3:62:FA:A7:AB:D7)
V 17:09...
Hi All,
We've build multiple applications based on Thread. Now, with time our applications are getting bigger and complex, so we decided to integrate FreeRTOS into our applications...
I'm trying to get Multicell Location working.
At the moment it won't compile.
I've tried with Skyhook key and NRF key.
prj.conf as follows:
I'm using nRF9160DK_nRF9160ns...
