after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi Nordic,
We created a firmware based on the eddystone example in nRF5_SDK_17.0.0_9d13099,
I modified the macro APP_CONFIG_ADV_INTERVAL_MS_MAX in es_app_config.h from...
Hi,
After connect, we add services/characteristics, and call sd_ble_gatts_service_changed(),but it also return BLE_ERROR_GATTS_SYS_ATTR_MISSING. I have enable NRF_SDH_BLE_SERVICE_CHANGED...
I'm struggling to get my nRF52840 DK to appear in nRF Connect (3.6.1), but I have no issues with connecting the nRF52840 Dongle.
I have been using this hardware for a couple...
My aim is to use a nRF52832 for a Bluetooth peripheral device.
- I just started with a fresh SES V5.44 and downloaded the nRF SDK 17.0.2 - I imported the example "ble_app_hids_keyboard_pca10040_s112...
My product needs HMAC using sha256.
I looked at the \nRF5_SDK_17.0.0_9d13099\examples\crypto\nrf_crypto\hmac
It has been written for nrf52832. My product uses nrf52810...
After the call is initialized and started (nrf_drv_pdm_init nrf_drv_pdm_start), the callback is executed only once. It needs to be re-nrfx_pdm_buffer_set each time in the...
Dear friends,
I flashed a mesh serial example and fetched the Composition Datacomposition data by composition_data_get(), as below code:
I wonder the meaning about the...
I have implemented nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_beacon\pca10040\s132\arm5_no_packs code for iBEACON.
I am able to run it and able to see the advertised...
Hello,
I was using the send example which is located in C:\v1.5.1\zephyr\samples\drivers\lora and trying to send a message to an Arduino LoRa gateway.
However, I found...
Hello everyone,
I am stuck at a problem that I cannot resolve myself but I see that other people in the forum don't experience such a behaviour of their nrf52832s.
I want...
Hello,
I've been using SES for ARM (Nordic Edition) V4.16 (64-bit). I am working with nRF9160 sample code. While attempting to explore the code, when I right click on...
The program flow of the slave is to sample the analog signal source through the saadc and then send it to the host through the nus. When debugging on nrf52dk, configure the...
Hi,
In my main function, I just call a acceleration_read function to get data from the accelerometer sensor and call a NRF_LOG_INFO function.
But there're something wrong...
