Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
HI,
I am working NRF52810 with SDK 17.
I am able to pair my nordic device to mobile. but after pairing I want to send some data/receive some data.
how can I achieve...
In SDK 17.0.2, most places it looks like BLE_GAP_ROLE_CENTRAL is allowed to be undefined, except in nrf_ble_gatt.c line 142. Was there supposed to be "#ifdef BLE_GAP_ROLE_CENTRAL...
Hi Team, I am prototyping a product that includes DFU OTA using nRF52832. To get familiar with the topic, I am experimenting with the buttonless DFU example.
It is working...
Hi Nordic!
I am completely new to the Nordic MCU. Please, where can I find all the information (technical datasheet) about the NRF52840? What peripherals can I connect on...
Hello,
I want to use radio to send and receive data periodly. So I refer TimeSlot API in ' devzone.nordicsemi.com/.../setting-up-the-timeslot-api',and also refer the radio...
I am trying to implement the AWS FOTA sample from SDK V1.4.2.
I have already implemented the AWS IOT sample which works fine.
However, the AWS FOTA fails with mqtt_connect...
Hello there, I just try to demonstrate TCP examples in NRF5 SDK 15 and 16.
I got two linux boards, one of them Allwinner V3S with Debian Bullseye and the other one is...
Hi,
I'm trying to configure nRFgo studio, but after connecting the device to my PC via RS 232, nRFgo studio can't recognize the com port.
Where can I find a user manual...
I'm working on pca10059(nRF52840 dongle) to send UART data over bluetooth to another device.
My test environment is,
Arduino Uno to send uart signal using "mySerial.write...
In nRF5 SDK for mesh v5.0, what kind of information (related to provisioing and communication) is stored in the internal flash memory?
And what is the API for accessing...
Hi , I have real ECG device with 2 Click and I almost got NRF52840 with PCA10056 development board. I want to put the analog signal from the ECG device to the ADC on the development...
hi support team,
customer is using 5340 1M i2c interface, and we find out that ncs 1.5 still don't have 1M driver, we have to modify the source code，may i ask the when R&D...
Hi,
I am saving temp data along with timestamps in the internal memory and sending it through ble.
if during transfer the queue becomes full (NRF_ERROR_RESOURCES), I am...
Hello all,
I'm developping a firmeware to test the bluetooth inside of our case. So i want to start DTM with a bluetooth command.
The command goes right, but the dtm_init...
We are switching between two modes of ADC sampling in our application:
single shot - Consists of a routine -> Init saadc -> convert a sample of one ADC channel -> uninit...
