Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am trying to use nrfsniffer to debug connection related issues.
We have a ble connection between central and peripheral and we are sending status updates to the peripheral...
I am building an application nrf52840 SDK v17.0.2 soft device is S140 with Segger embedded studio.
Application is to send advertisement data in one single channel (say channel...
Hi
I am trying to Update the Soft Device from 6.1.1 to 7.0.2 (SDK 15 to 17). Using an NRF52840 Dev Kit I am using nRfgo Studio to:
Erase all
Program the new Soft Device...
Hi
I am trying to Update the Soft Device from 6.1.1 to 7.2.0 (SDK 15 to 17). Using an NRF52840 Dev Kit I am using "nRfgo Studio" to:
Erase all
Program the new Soft...
hello,
i am using nrf52840 in our customised board and i am getting this error while debugging the application
4<debug> nrf_sdh_ble: RAM starts at 0x20004230 <error> app...
Hi all,
Debugging via RTT in Segger Embedded Studio stops working after DFU, however if I connect via JLinkExe + JLinkRTTClient I can still interact and debug via RTT.....
Greetings,
I am currently using nRF5 SDK 16.0.0, Softdevice s140_nrf52_7.0.1_softdevice.hex, and Mesh SDK 4.2.0. I migrated all my code base from nRF5 SDK 15.3.0, Softdevice...
Is there a way to obtain context on when a particular BLE transmission ends
RADIO_STATE_STATE_TxDisable == NRF_RADIO->STATE
An by context I mean to know what handle was...
Hello all i want to do a task that is control another LED using ble_app_blinky. In the ble_app_blinky project a characteristic is used to control an onboad LED. I have connected...
Hello
I have a custom board with nRF52840 and have migrated from TWI legacy driver to nrfx_twim. Im trying to communicate with accelerometer and gyroscope chip. With legacy...
Hello forum,
I have a new project that requires Bluetooth connectivity and I think that the nRF52805 suits me best due to its very small size.
The nRF52805 would work...
Hi, I would like to test sample bluetooth code ( ex: central) with nrf5340 dk, what's the difference between central for cpuapp and cpunet ? which one i have to load , cpunet...
I am trying to read Manufacturer Specific Data from a non-connectable advertisement packet from a pressure sensor.
I followed the example in https://devzone.nordicsemi.com...
I have used the nrf9160 development board and it can works rightly. But from this week, it doesn't work. I can download my code to the board, but it doesn't work. When I press...
