after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Dear all and Nordic Staff:
Thanks for your support as usual.
I have a new application project with BLE and Zigbee dual stack protocol for industry market.
May you suggest...
One of the nRF52840-DK (PCA10056 v2.0.0) we are using as a programmer and debugger for our custom board has started repeatedly resetting the custom board whenever an RTT console...
ble_gatt_db.h and ble_db_discovery.h each contain #defines that are problematic, BLE_GATT_DB_MAX_CHARS and BLE_DB_DISCOVERY_MAX_SRV respectively.
Of course, one can change...
We use NRF52832 in the remote control of the car。 We measured the average current of power consumption at about 1uA.Every 300ms, the current curve bounces to the transient...
I would like to use the RTC in the nRF52833 as a clock-calendar. The device will normally be powered by the USB Vbus but must have power fail protection to insure the integrity...
Hello,
I would like to create a star network (with no routers) in ZigBee with nRF52 (also with multiprotocol BLE). I examined the relevant SDK (nRF5_SDK_for_Thread_and_Zigbee_v4...
My setup is a custom board with the nRF52832 and a remote BLE client e.g. nRF Connect tool kit on an Android phone.
The application periodically broadcasts a 'beacon' but...
I am using Nordic SDK v15.3.0.
I have set all the required parameters and content before I call the API "ble_advdata_encode(..)". I ran into two issues one of which I can...
I am using SDK version 15.3.0 and would love to know what exactly is the meaning of the first parameter "size of event" used in the macro APP_SCHED_INIT(X,Y)?
I treat "events...
I have installed Segger Embedded Studio for ARM V5.32a.
I am trying to build the example project under ble_peripheral/ble_app_uart.
I have installed these packages in...
Dear community, Dear Nordic engineers,
For some reason I cannot connect my custom board to the nordic cloud. Previously I have followed the described procedures with the...
Hello,
I have a custom nrf52832 board with a SparkFun HX711 load cell.
I've developed my firmware using Segger Studio testing my data through a BLE connection with the...
Hi,
I ported my application from SDK 12.3 to SDK 17.0.2. Unfortunatley it isn't running on the board, but the only thing I have is a warning which I'm hoping is the issue...
