Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Open LTE Link Monitor OK, but point connections appear with the following blank interface
Here's the LTE Link Monitor that shows the blank
LTE Link Monitor is...
Hello,
I am using NRF52840 with SDK 16.0.0 and Mesh SDK 4.1.0
.I am trying to use SAADC with BLE Mesh(SDK 4.1.0). I used default example of SAADC with multiple channel...
I am new to nRF9160 development board. I have just opened the board and tried to connect following the startup instructions. I was able to see LED 3 and LED 4 blink the first...
Hi all,
I am trying to get a hang of SES platform(Using the nRF52840 Preview DK, SDK 15.3) and it's my first few trails with it. I am trying something very basic now to...
I want to read characteristics (central needs read data from peripheral whenever he want ) but don’t want to use notification.
I am trying this with authorization but it...
I have already set up a successful sender and receiver. The receiver was using an arduino board and the sender a avr at90usb162. I have now removed the arduino and moving...
Hello,
My project is using Lora + radar + ble so I am trying to let 1 radio tx at a time for FCC and power.
For this, I found time slot API and extension at the links...
Dear Nordic Team,
I am working on a product which implements OTA DFU(buttonless DFU inside). So far everything works fine and the updates are working.
The question is...
Hello,
I am using nRF52840 S140 V7.0.1. I am using ble_app_multirole_lesc example. I changed roles from “Central and Peripheral” to “Observer and Broadcater”.
My understanding...
Hi
nRF52840 SWD is push pull or open drain type?
And we want add level shifter between J-Link and nRF52840, do you have recommend level shifter PN? Or what type of level...
Current latest JLink firmware won't allow PPK working with DK RTT debugging.
The cause is the JLink chip on the DUT board won't put the SH_SWO/SH_SWCLK/SH_SWDIO in hi-Z...
I am working with the chip ISP4520 which combine Nordik NRF52832 and LORA semtech. I use nORDIC sdk 14. I burn the FW to the chip using Nordic development kit connected by...
Hi,
I tried a light-switch example from SDK for mesh ver 4.1.0 on two nRF52840 DKs(first board with client and the second with server). I configured them with nRF Mesh app...
Hi,
I have an unkown problem in my nrf52 application. It happens rarely, so I have no idea where to look at the moment. The only thing I know is that the WDT works and resets...
I have browsed through the forum and i couldn't find a similar question, so here I ask :
I have an application running a modified example of the Mesh Client & Server merged...
